Wastegate Solenoid - Remove and Install
拆卸步骤
开始:
- 将蓄电池断路开关转到断开位置。
- 将软管组件 (4) 从废气旁通阀电磁阀 (5) 上拆下。
Show/hide table
图 1 | g02720973 |
Show/hide table
图 2 | g02720986 |
- 在所有软管组件上做临时标记,以确定在废气旁通阀调节器 (5) 上的位置。
- 拆下软管卡箍 (2) 。 将软管组件 (3) 从废气旁通阀电磁阀 (5) 上断开。
- 拆下软管卡箍 (6) 。 将软管组件 (7) 从废气旁通阀电磁阀 (5) 上断开。
- 拆下软管卡箍 (9) 。 将软管组件 (8) 从废气旁通阀电磁阀 (5) 上断开。
- 拆下六角头螺栓 (1) ,并将废气旁通阀电磁阀从支架 (10) 上拆下。
- 如有必要,将螺栓 (11) 和支架 (10) 从水温调节器壳体上拆下。
安装步骤
- 确保废气旁通阀调节器的所有部件清洁、无磨损和损坏。 如有部件磨损或损坏,必要时将废气旁通阀调节器作为一个整体进行更换。
- 如有必要,将支架 (10) 定位到水温调节器壳体上。 确保支架正确定位到位置 (A) 的套管上。
Show/hide table
图 3 | g02721016 |
Show/hide table
图 4 | g02720973 |
- 安装螺栓 (11) 并用手拧紧螺栓至扭矩为 10 N·m (89 lb in)。
- 将废气旁通阀电磁阀 (5) 定位到支架 (10) 上。 将六角头螺栓 (1) 安装到废气旁通阀电磁阀 (5) 上。 将六角头螺栓 (1) 拧紧至扭矩为 10 N·m (89 lb in)。
- 将软管 (8) 定位到废气旁通阀电磁阀上。 牢固地拧紧软管卡箍 (9) 。
- 将软管 (7) 定位到废气旁通阀电磁阀上。 牢固地拧紧软管卡箍 (6) 。
- 将软管 (3) 定位到废气旁通阀电磁阀上。 牢固地拧紧软管卡箍 (2) 。
- 确保软管不与任何其他发动机部件接触。
- 将线束组件 (4) 连接到废气旁通阀电磁阀上。
End By: 将蓄电池断路开关转到 接通位置。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C3.4B Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbochargers
C3.4B Engines for Caterpillar Built Machines Turbocharger - Remove - Side Mounted Turbochargers
C3.4B Engines for Caterpillar Built Machines Turbocharger - Install - Side Mounted Turbochargers
C3.4B Engines for Caterpillar Built Machines Turbocharger - Install - Top Mounted Turbochargers
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Rear Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Side Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (DPF) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
C3.4B Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C3.4B Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C3.4B Engines for Caterpillar Built Machines Water Pump - Install
C3.4B Engines for Caterpillar Built Machines Water Pump - Remove
C3.4B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
G3516C and G3516E Gas Engines Junction Box
2012/08/10 A New Turbocharger Housing is Used on Certain 3512B Engines {1052, 1065}
C3.4B Engines for Caterpillar Built Machines Cylinder Head - Install
C3.4B Engines for Caterpillar Built Machines Cylinder Head - Remove
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove - Through Flow Diesel Particulate Filter
Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239} Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239}
CX48-P2300 Petroleum Transmission Transfer Gears - Remove and Install - Upper
3512C and 3516C Marine Engines Engine Oil Lines
2012/05/08 Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}