Control Manifold - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 6V-5219     | 螺栓     | 2     |
B     | 1P-1853     | 挡圈钳     | 1     |
开始:
- 拆下控制歧管。 请参考拆解和装配, "控制歧管 - 拆卸和安装"。
- 将螺栓 (1) 和安全阀 (2) 从控制歧管 (3) 上拆下。
Show/hide table
图 1 | g03012621 |
- 拆下塞 (4) 和 O 形密封圈。 将螺栓 (5) 、垫圈、盖 (6) 和 O 形密封圈从安全阀 (2) 上拆下。
Show/hide table
图 2 | g03015662 |
- 拆卸螺钉 (8) 之前,标记尺寸 (X) 以便安装。 拆下螺钉 (8) 、锁紧螺母 (10) 和垫圈 (11) 。
Show/hide table
图 3 | g03014296 |
(X) 从螺钉 (8) 顶部到盖 (7) 表面的尺寸。 |
Show/hide table
图 4 | g03014276 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装工具 (A) 。 拆下螺钉 (8) 、锁紧螺母 (10) 和垫圈 (11) 。
- 均匀地拆下螺栓 (9) ,直至盖 (7) 接触到工具 (A) 。 拆下螺栓 (9) 。 松开工具 (A) ,直至释放所有的弹簧张力。 拆下工具 (A) 。
- 拆下负载活塞 (14) 、弹簧 (13) 和滑阀组件 (12) 。
Show/hide table
图 5 | g03016080 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 将缓动阀 (15) 从滑阀组件 (12) 上拆下。
Show/hide table
图 6 | g03016256 |
- 使用工具 (B) 拆下挡圈 (19) 。 将护圈 (18) 、弹簧 (17) 和钢球 (16) 从滑阀组件 (9) 上拆下。
Show/hide table
图 7 | g03016308 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 拆下螺塞 (21) 和 O 形密封圈。
Show/hide table
图 8 | g03016036 |
Show/hide table
图 9 | g03016436 |
- 使用工具 (B) 拆下挡圈 (20) 。
- 拆下垫圈 (24) 和安全阀 (22) 。 从安全阀 (22) 上拆下 O 形密封圈 (23) 。
- 断开线束组件 (27) 。 拆下螺栓 (25) 后拆下调制阀 (26) 。
Show/hide table
图 10 | g03013576 |
- 拆下螺纹接头组件 (28) 和 O 形密封圈。 将 O 形密封圈 (30) 从调制阀 (26) 上拆下。 拆下螺母 (31) 、垫圈和线圈组件 (29) 。
Show/hide table
图 11 | g03016539 |
- 对其余调节阀重复步骤12到13。
- 拆下螺栓 (33) 和板 (32) 。
Show/hide table
图 12 | g03018439 |
Caterpillar Information System:
2012/05/08 Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
3512C and 3516C Marine Engines Engine Oil Lines
CX48-P2300 Petroleum Transmission Transfer Gears - Remove and Install - Upper
Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239} Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239}
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove - Through Flow Diesel Particulate Filter
C3.4B Engines for Caterpillar Built Machines Cylinder Head - Remove
C3.4B Engines for Caterpillar Built Machines Cylinder Head - Install
2012/08/10 A New Turbocharger Housing is Used on Certain 3512B Engines {1052, 1065}
G3516C and G3516E Gas Engines Junction Box
C3.4B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C3.4B Engines for Caterpillar Built Machines Water Pump - Remove
C3.4B Engines for Caterpillar Built Machines Water Pump - Install
3500C Marine Engines Engine Oil Filter
G3516 Engines Engine Oil Pump
2012/04/30 New Software Is Now Used for Certain Tier 4 Interim Commercial Engines {1920}
2012/04/24 Turbocharger Surge on Certain G3500C and G3500E Engines that are Equipped with Dual Turbochargers {1052}
2012/04/30 Improved Fuel Injector O-Ring Seals Are Used on Certain Machine Engines {1251, 1290}
2012/04/30 Improved Fuel Injector O-Ring Seals Are Used on Certain Commercial Engines {1251, 1290}
3500C Marine Engines Engine Oil Sump Pump
3512C and 3516C Marine Engines Coolant Level Switch
3500C Marine Engines Engine Oil Sump Pump
Water Temperature Regulator on Certain C6.6 and C4.4 Engines{1355, 1380} Water Temperature Regulator on Certain C6.6 and C4.4 Engines{1355, 1380}
3512C and 3516C Marine Engines Crankshaft
3500B and 3500C Marine Engines Fuel Filter (Primary)