Display Module - Flash Program
Flash the Software onto the Display
The display is shipped without the application software installed. Use the following procedure in order to flash the application software into the display.
- Caterpillar Electronic Technician (CAT ET)
- Communication Adapter
- 345-7489 Monitor Harness As
Show/hide table
| Part Number | System | Notes |
|---|---|---|
| 440-2674 | Object Detection System | Radar and Vision |
| 440-2677 | Object Detection System (Vision Only) | Vision |
Perform the following procedure in order to flash program the ECM. The ECM is flashed in order to upgrade the software. Flash programming of the ECM must be done if the ECM has been replaced. Caterpillar Electronic Technician (Cat ET) contains the program WinFlash. WinFlash is used in order to load the software into the ECM. The following procedure is used in order to flash the software into the display.
- Ensure that the key start switch and the disconnect switch are in the OFF position.
- Disconnect the center 12-pin connector from the display.
- Connect the 345-7489 Monitor Harness As that is supplied with the cab kits between the following:
- System harness for the display and the center connector on the display.
- Connect the 7X-1425 Data Link Cable As between the 7X-1700 Communication Adapter Gp and Cat ET.
- Connect the 139-4166 Data Link Cable As between the 7X-1700 Communication Adapter Gp and the diagnostic connector of the machine.
- Use WinFlash in order to load the software.
- Disconnect the 345-7489 Monitor Harness As that is supplied with the cab kits from the following:
- System harness for the display and the center connector on the display.
- Connect the 12-pin connector of the system harness to the center connector of the display.
- Turn the disconnect switch and the key start switch to the ON position.
- Verify that the display turns ON and the Caterpillar Object Detection application launches.
Caterpillar Information System:
Cat® Detect Object Detection System Display Module - Replace
Cat® Detect Object Detection System Wiring Harness (Short Circuit) - Test
Cat® Detect Object Detection System Wiring Harness (Open Circuit) - Test
Cat® Detect Object Detection System Electrical Connector - Inspect
Cat® Detect Object Detection System Object Detection Sensor - Adjust
Cat® Detect Object Detection System Object Detection Sensor - Calibrate
2014/06/13 Repairing Expansion Tank Support Brackets for Certain 3500 Engines {1354}
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing
C13, C15, and C18 Tier 4 Final Engines Flywheel
C32 Marine Generator Set Product Lifting
C13, C15, and C18 Tier 4 Interim Engines Variable Valve Actuator Response - Test
CX31 On-Highway Transmission Transmission Planetary - Assemble - Retarder
Cat® Detect Object Detection System System Schematic
C-12 Engine Maintenance Interval Schedule
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators General Information
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Components
Updated Torque Value for the Magnetic Plug on Multiple Hydraulic Systems of Certain CAT Products {5050, 7000} Updated Torque Value for the Magnetic Plug on Multiple Hydraulic Systems of Certain CAT Products {5050, 7000}
Electrical Wiring Connection Modification for 1400 Frame Generator Space Heater{1408, 4450, 7274} Electrical Wiring Connection Modification for 1400 Frame Generator Space Heater{1408, 4450, 7274}
2011/10/13 Remanufactured Cylinder Pack Updates and Orientation Requirements for Certain C-16 and 3456 Engines {1214, 1239, 1331}
2011/11/02 Remanufactured Cylinder Pack Updates and Orientation Requirements for Certain C-16 and 3456 Engines {1214, 1239, 1331}
295-0048 Bulk Fuel Filtration Group 300 GPM Flow Rate{0374, 0599, 0680, 0706, 1250, 1261, 1280} 295-0048 Bulk Fuel Filtration Group 300 GPM Flow Rate{0374, 0599, 0680, 0706, 1250, 1261, 1280}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System One-Way/One or Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust
320E and 323E Excavators Machine System Specifications Control Valve
320E and 323E Excavators Machine System Specifications Boom - 5.7 m (18.62 ft)