Electrical Connector - Inspect
Intermittent electrical problems are often caused by poor connections. Use the following checks as a reference for inspecting connectors.
- Check the connection of the connectors.
- Ensure that the locking rings are properly locked.
- Ensure that locking clips are used on Sure Seal connectors.
- Ensure that the center of the connector is tight.
- Ensure that the connector pins and sockets align properly.
- Check the wires at the connector.
- Ensure that the wires enter the back of the connector straight.
- Ensure that each wire is properly crimped into the proper connector contact.
- Ensure that each connector contact is properly locked into the connector contact. When the connector contact is locked properly, the contact (wire) cannot be pulled out of the connector body without excessive force.
- Check each wire for nicks or signs of abrasion in the insulation.
- Check for moisture at the connector.
- Check for damaged connector seals or lost connector seals.
- Check for missing or loose wire hole plugs.
- Check for wires that do not enter the connector properly.
- If the wires enter the connector at an angle, there may not be a good seal between the connector and the wire insulation.
- Moisture can enter the connector through the wire insulation.
- Check for dirty contacts or corroded contacts.
- Clean contacts with a cotton swab or a soft brush and denatured alcohol only.
- Check each pin and each socket.
- Check each contact of the connector for a snug fit by using a new pin and socket. The new contact should stay connected if the connector is held with the contacts that are facing down.
Caterpillar Information System:
Cat® Detect Object Detection System Object Detection Sensor - Adjust
Cat® Detect Object Detection System Object Detection Sensor - Calibrate
2014/06/13 Repairing Expansion Tank Support Brackets for Certain 3500 Engines {1354}
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing
C13, C15, and C18 Tier 4 Final Engines Flywheel
C32 Marine Generator Set Product Lifting
C13, C15, and C18 Tier 4 Interim Engines Variable Valve Actuator Response - Test
CX31 On-Highway Transmission Transmission Planetary - Assemble - Retarder
CX31 On-Highway Transmission Transmission Planetary - Disassemble - Retarder
Cylinder Liners are Cracking after Engine Rebuilds on Certain 3456 and C16 Engines{1201, 1216} Cylinder Liners are Cracking after Engine Rebuilds on Certain 3456 and C16 Engines{1201, 1216}
Certain 336D and 345D Excavators have Excess Paint that Causes Hydraulic Fluid to Leak from a Pressure Sensor{5057, 5456} Certain 336D and 345D Excavators have Excess Paint that Causes Hydraulic Fluid to Leak from a Pressure Sensor{5057, 5456}
CX31 On-Highway Transmission Modulating Valve (Transmission Clutch) - Remove and Install
Cat® Detect Object Detection System Wiring Harness (Open Circuit) - Test
Cat® Detect Object Detection System Wiring Harness (Short Circuit) - Test
Cat® Detect Object Detection System Display Module - Replace
Cat® Detect Object Detection System Display Module - Flash Program
Cat® Detect Object Detection System System Schematic
C-12 Engine Maintenance Interval Schedule
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators General Information
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Components
Updated Torque Value for the Magnetic Plug on Multiple Hydraulic Systems of Certain CAT Products {5050, 7000} Updated Torque Value for the Magnetic Plug on Multiple Hydraulic Systems of Certain CAT Products {5050, 7000}
Electrical Wiring Connection Modification for 1400 Frame Generator Space Heater{1408, 4450, 7274} Electrical Wiring Connection Modification for 1400 Frame Generator Space Heater{1408, 4450, 7274}
2011/10/13 Remanufactured Cylinder Pack Updates and Orientation Requirements for Certain C-16 and 3456 Engines {1214, 1239, 1331}
2011/11/02 Remanufactured Cylinder Pack Updates and Orientation Requirements for Certain C-16 and 3456 Engines {1214, 1239, 1331}