Cylinder Head
Show/hide table
| |
| Illustration 1 | g02592153 |
|
Bolt tightening sequence | |
Show/hide table
| |
| Illustration 2 | g02592118 |
|
(3) Oil gallery
(5) Oil holes | |
Show/hide table
| Specification for 274-5129 Cylinder Head Gp and 298-6405 Cylinder Head Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 32 | 124-1855 Bolt | Use Use Use Use the following procedure in order to tighten the cylinder head bolts: Before assembly, apply 4C-5592 Anti-Seize Compound to the bolt threads and to both sides of the washers for bolt 1 through bolt 26. 1. Tighten the bolt 1 through bolt 26 in a numerical sequence to 2. Tighten the bolt 1 through bolt 26 in a numerical sequence to 3. Again, tighten the bolt 1 through bolt 26 in a numerical sequence to 4. Tighten the bolt 27 through bolt 39 in a numerical sequence to |
| 20 | 124-1854 Bolt | ||
| 26 | 248-0036 Bolt | ||
| 2 | 24 | 2W-0482 Taperlock Stud | Install the taperlock studs so that the letter "Y" is showing.
Torque to |
| A | - | - | Orientation of the bushing joint is 20 |
| 4 | 7 | 216-5582 Bushing | Installation depth of the bushing for camshaft is important. Install the bushing to the following depths:
Dimension (B) is Dimension (C) is Dimension (D) is Dimension (E) is Dimension (F) is Dimension (G) is Dimension (H) is |
Show/hide table
| NOTICE |
|---|
|
Camshaft bearings must be installed into their correct position. Failure to do so will result in engine damage. |
Show/hide table
| |
| Illustration 3 | g02592138 |
|
Top view | |
Show/hide table
| |
| Illustration 4 | g02594826 |
|
Bottom view | |
Show/hide table
| Specification for 274-5129 Cylinder Head Gp and 298-6405 Cylinder Head Gp | |||
| Item | Qty | Part | Specification Description |
| 6 | 36 | 3B-0623 Cup Plug | Before assembly, apply Loctite 540 to the bore of the cup plugs. |
| 7 | 6 | 263-4920 Injector Sleeve | Before assembly, apply green Loctite 620 to press fit diameter of the lower end of injector sleeves.
Press the injector sleeve to the bottom of the face (8). |
| R | - | - | Installation depth for cup plugs is |
Caterpillar Information System:
C175-16 Petroleum Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
3500B and 3500C Marine Engines Vibration Damper Guard
797F and 797F XQ Off-Highway Trucks Machine Systems Upper and Lower Link (Suspension) - Install
797F and 797F XQ Off-Highway Trucks Machine Systems Upper and Lower Link (Suspension) - Remove
Cat Water Delivery System (WDS) Service Ports
3516C IMO III Petroleum Engines Engine Oil Cooler - Install
CG137-08 and CG137-12 Engines Carburetor Air/Fuel Ratio - Check/Adjust
C3.4B Industrial Engine Diesel Particulate Filter - Clean
C27 and C32 Generator Set Engines Cylinder Head Valves
3500B Engines for Caterpillar Built Power Modules Vibration Damper Guard
3500 Engines Flywheel Housing Cover
3500 Engines Stub Shaft (Front)
G3500 Engines Vibration Damper
C175-16 Engine for Off-Highway Truck/Tractors Engine Oil Pump
C32 Marine Engines Cylinder Head
3500 Engines for Caterpillar Built Generator Sets Accessory Drive (Lower Left Hand)
C32 Marine Engines Engine Oil Filter Base
C32 Marine and Auxiliary Marine Engines Exhaust Manifold
C32 Marine and Auxiliary Marine Engines Exhaust Manifold
C32 Marine Engines Engine Oil Filter Base
Special Installation Instructions for the 379-3359 Speed Switch Assembly {1400, 1915, 7400, 7426, 7451} Special Installation Instructions for the 379-3359 Speed Switch Assembly {1400, 1915, 7400, 7426, 7451}
349F and 352F Excavators Machine System Specifications Cab - Front Window Guard
2011/07/11 A Different Vibration Damper Guard Is Available for Certain 3512C Petroleum Engines {1205}