Torque Converter Housing - Install
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1U-9200 | Lever Puller Hoist Gp | 1 |
| B | 138-7575 | Link Bracket | 3 |
| C | 9S-3263 | Thread Lock Compound | 1 |
| D | 385-4000 | Seal Installation Tool | 1 |
| E | 6V-2055 | Grease | - |
- Install integral seal (7) . Apply Tooling (E) onto ring seals (8) . Install ring seals (8) .
Note: Insure that ring seals (8) are fully compressed into the grooves of the rotating clutch.
Show/hide table
 | |
| Illustration 1 | g03740038 |
- Use Tooling (A) , Tooling (B) , and a suitable lifting device in order to install torque converter housing (4) . The weight of torque converter housing (4) is approximately 79 kg (175 lb).
Show/hide table
 | |
| Illustration 2 | g02395880 |
Show/hide table
 | |
| Illustration 3 | g02395917 |
- Apply Tooling (C) onto the housing top face, the washer, and bolt (6) . Install bolt (6) . Install bolts (5) . Tighten bolts (5) and bolt (6) to a torque of 100 ± 20 N·m (73 ± 14 lb ft).
Note: Remove the excess sealant from bolt (6) , the washer, and the housing spotface.
- Connect harness assembly (3) and install the connecting hardware.
Show/hide table
 | |
| Illustration 4 | g02395878 |
- Connect harness assembly (2) .
Show/hide table
 | |
| Illustration 5 | g02395876 |
- Remove lip seal (1) from the packaging. Be careful not to touch the inside diameter. Inspect lip seal (1) for damage. Ensure that the spring is installed properly before installing the lip seal onto Tooling (D) . Apply a thin film of the fluid that is being sealed to the outside diameter of lip seal (1) prior to installation. Install lip seal (1) onto Tooling (D) so that the "spring open" side is oriented away from the driving face of Tooling (D) . Ensure that the sealing surface of the torque converter housing is clean and free of damage. Use Tooling (D) to install lip seal (1) in the torque converter housing. Use Tooling (D) in order to drive in the lip seal. Install lip seal (1) to the depth that is shown. A "ring" sound will indicate that the lip seal is fully seated.
Note: Ensure that Tooling (D) is in good condition and free of defects. Store Tooling (D) in a VCI bag in order to prevent rust and contamination.
Show/hide table
 | |
| Illustration 6 | g02395857 |
Show/hide table
 | |
| Illustration 7 | g02395998 |
End By:
- Install the gear pump. Refer to Disassembly and Assembly , "Gear Pump (Torque Converter and Transmission) - Install".
- Install the torque converter. Refer to Disassembly and Assembly , "Torque Converter - Install".
Caterpillar Information System:
CX31 On-Highway Transmission Torque Converter Housing - Remove
3600 Distillate Fuel Engines Engine Valve Lash - Check
3600 Distillate Fuel Engines Engine Speed/Timing Sensor - Clean/Inspect
3600 Distillate Fuel Engines Engine Air Precleaner - Check/Clean
3600 Distillate Fuel Engines Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3600 Distillate Fuel Engines Coolant Temperature Regulator - Replace
3600 Distillate Fuel Engines Coolant Sample (Level 2) - Obtain
3600 Distillate Fuel Engines Coolant Sample (Level 1) - Obtain
3600 Distillate Fuel Engines Coolant Level - Check
3600 Distillate Fuel Engines Coolant Extender (ELC) - Add
3600 Distillate Fuel Engines Coolant (ELC) - Change
3600 Distillate Fuel Engines Coolant (DEAC) - Change
3600 Distillate Fuel Engines Exhaust Piping - Check
3600 Distillate Fuel Engines Metal Particle Detector - Inspect/Clean
Reconditioning Dimensions for Carrier Rollers {4154, 4180} Reconditioning Dimensions for Carrier Rollers {4154, 4180}
2011/02/02 New Software is Now Used on Current Production C9, C11, C13, C15, C18, and Certain C27 Industrial Engines {1901, 1920}
C6.6 Industrial Engine Maintenance Interval Schedule
826K Landfill Compactor Diesel Particulate Filter - Clean - Emission Related Component
C9.3 Industrial Engine and CX31-P600-C9I Petroleum Power Train Package Diesel Particulate Filter - Clean/Replace
3516C Locomotive Engines Aftercooler - Remove and Install
CG137-08 and CG137-12 Industrial Engines Catalytic Converter Pressure - Test
3600 Distillate Fuel Engines Fluid Recommendations
C7.1-XQ230 Rental Generator Set Turbocharger - Inspect
Maintaining the Protective Structure (ROPS/FOPS) Certification when Making Modifications To (ROPS/FOPS) {7323, 7325, 7715} Maintaining the Protective Structure (ROPS/FOPS) Certification when Making Modifications To (ROPS/FOPS) {7323, 7325, 7715}