Crankshaft - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 4C-9832 | 发动机翻转支架 | 1 |
B | 138-7576 | 连杆支架 | 2 |
开始:
- 拆卸摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 拆下飞轮壳体。 请参阅拆解和组装, "飞轮壳体 - 拆卸"。
- 拆卸前壳体。 请参阅拆解和组装, "壳体(前) - 拆卸"。
- 拆下活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
注意 |
---|
当活塞和连杆被推离轴箱时,没有拆卸摇臂轴组件和推杆可能会损坏气门。 为避免损坏气门,拆卸曲轴前拆卸摇臂轴组件和推杆。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (A) 将发动机转到水平位置。 发动机可用工具 (A) 或挡块支撑。 3516C 发动机的重量约为
9100 kg (20000 lb) 。注: 如果从发动机上拆卸活塞和连杆组件,则没必要从曲轴上拆卸配重。
Show/hide table图 1 g01124519 - 在配重 (2) 上贴上标记。 从曲轴上拆下螺栓 (1) 和配重 (2)。
注: 切勿重复使用螺栓 (1)。 用新的螺栓将配重固定到曲轴。
Show/hide table图 2 g01124522 注: 出于安装目的,对连杆盖和连杆进行编号。
- 拆下螺栓 (3 )。 拆卸连杆盖 (4) 并将连杆从曲轴中推出。
注: 确保曲轴上的轴径没有被连杆擦伤。
Show/hide table图 3 g01124538 - 在曲轴 (7) 的每一端都连上工具 (B)。 将适当的起吊设备连接在工具 (B) 上。 3516C 曲轴的重量约为
800 kg (1765 lb) 。 - 拆下螺栓 (5) 和主轴承盖 (6)。
- 从中心主轴承两侧卸下止推盘 (8)。
- 将曲轴 (7) 从缸体上拆下。
- 将主轴承上轴瓦从缸体上拆下。
- 从连杆上拆下连杆轴承上轴瓦。
Show/hide table
图 4 g01124543 - 如有必要,从曲轴的每一端拆卸螺栓 (9) 和曲轴齿轮 (10)。
Caterpillar Information System:
C4.4 Industrial Engine Product Lifting - Clean Emission Module
Installation of Improved Battery Charger for Certain C9, C15, and C18 Gensets{1401, 1406} Installation of Improved Battery Charger for Certain C9, C15, and C18 Gensets{1401, 1406}
Repair of Reaction Dowel Holes in Transmission Clutch Housings {3030, 3155, 3169} Repair of Reaction Dowel Holes in Transmission Clutch Housings {3030, 3155, 3169}
349F and 352F Excavators Machine System Specifications Recoil Spring
349F and 352F Excavators Machine System Specifications Swing Motor Lines
349F and 352F Excavators Machine System Specifications Control Valve
3516C Locomotive Engines Camshaft - Install
3516C Locomotive Engines Camshaft - Remove
3116 and 3126 Marine Engines Auxiliary Water Pump (Rubber Impeller) - Inspect
349F and 352F Excavators Machine System Specifications Control Valve
C32 Generator Set Overhaul Considerations
2011/01/10 A New Valve Bridge Is Available for Certain Truck Engines {1102, 1123}
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Startup
C32 Marine Generator Set Product Description
3500 Engines Crankshaft - Install
UPSB220 Uninterruptible Power Supply Emergency Power Off Connection
3512E Tier 4 Final Engines for Land Electric Drilling Engine Design
Facility and Equipment Layouts {4150} Facility and Equipment Layouts {4150}
Procedure for Installation of VR6 Voltage Regulator{4467} Procedure for Installation of VR6 Voltage Regulator{4467}
C32 Generator Set Generator Operation
Hose Products Reference Guide {0374, 0599, 0684, 0738, 5057} Hose Products Reference Guide {0374, 0599, 0684, 0738, 5057}
G3406 and G3412 Generator Sets Generator Bearing Temperature - Test/Record
3500 Generator Sets Rotating Rectifier - Check
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Speed Sensor (Transmission Output)