Air Shutoff - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
Show/hide table
如果不遵循正确的程序或不使用推荐的工具,可能会对人员造成伤亡。 为避免对人员造成伤亡,应使用推荐的工具遵循已经制定好的程序。 |
Show/hide table
在拆下进气切断装置前,拉动进气切断装置上的跳开关旋钮或按下紧急停止按钮,以释放叶片锁闩。 如果在拆下进气切断装置后释放叶片锁闩,可能导致严重的人身伤害。 |
- 手动释放空气切断阀。 拉动以释放空气切断阀上的旋钮。 确保空气切断阀上的指示器径直向下指向"关闭"位置。 如果空气切断阀不触发,请参阅故障诊断与排除, "空气切断阀系统"。
Show/hide table
图 1 g02405236 - 断开线束组件 (3)。
- 将适当的起吊设备连接到弯头 (2) 上。 拆下螺栓 (1) 和垫圈。 拆下螺栓 (8) 和 (7)。 拆下弯头 (2)。
- 将管组件 (5) 从空气切断阀 (6) 上断开。
- 断开线束组件 (4)。 拆下进气歧管上的卡箍组件 (9)。
- 拆下空气切断阀 (6) 和密封垫。
注: 检查进气管中有无碎屑。
- 对发动机的另一侧重复此步骤。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 按与拆卸相反的顺序安装空气切断阀 (6)。
- 复位空气切断阀上的指示器。 确保指示器上的箭头径直向上指向"打开"位置。
- 测试空气切断阀 (6) 是否正常工作,并参阅操作和保养手册, "空气切断阀"。
Caterpillar Information System:
C4.4 Industrial Engine Air Compressor - Single Cylinder
C4.4 Industrial Engine Air Compressor - Twin Cylinder Compressor
525D, 535D, 545D, 555D Wheel Skidder Fuel System Primary Filter (Water Separator) Element - Replace
C4.4 Industrial Engine Accessory Drive - SAE "B"
C4.4 Industrial Engine Accessory Drive
C7.1 Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C9.3 Engines for Caterpillar Built Machines Pressure Sensor (ARD Combustion Air) - Remove and Install
348-5430 Multi-Tool Gp 2 {0709, 0769, 0785} 348-5430 Multi-Tool Gp 2 {0709, 0769, 0785}
317-7492 Wireless Radio{7338} 317-7492 Wireless Radio{7338}
C27 and C32 Tier 4 Engines Component Location
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
C27 Generator Set Engines Air Inlet and Exhaust System - Inspect
C4.4 Industrial Engine Exhaust Sensor and Lines (NRS)
C175-16 Locomotive Engine Lifter Group
C7.1 Industrial Engine Fuel System Secondary Filter - Replace
C9.3 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Turbocharger - Inspect
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Product Lifting
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Plate Locations and Film Locations
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Manual Stop Procedure
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Starting the Engine
C4.4 Industrial Engine Engine Design
C27 and C32 Tier 4 Engines Configuration Parameters
C4.4 Industrial Engine Cylinder Head - Inspect