After Stopping Engine
注: 检查发动机机油之前，停止运行发动机至少 10 分钟以便使发动机机油有充分时间回到油底壳。
- 检查曲轴箱油位。 保持机油油位在机油油尺的"最小（MIN）"标记与"最大（MAX）"标记之间。
- 如有必要，进行较小的调整。 修理每一处泄漏并拧紧任何松动的螺栓。
- 请注意要求的保养周期。 按本操作和保养手册, "保养周期表"所述进行保养。
- 加满燃油箱以防止油箱中积聚湿气。 燃油箱不要加油过满。
Show/hide table
| 注意 |
|---|
|
在本操作和保养手册中的加注容量和建议标题下只能使用推荐的防冻剂/冷却液混合液。不这样做会造成发动机损坏。 |
- 让发动机冷却下来。 检查冷却液液位。
- 如果预料到结冻温度，要检查冷却液的防冻保护是否正确。 必须保护冷却系统，以防其在预计的最低外部温度下结冻。 如果必要，添加正常的冷却液/水混合液。
- 对所有被传动的设备进行必需的定期保养。 此保养会在 OEM 的使用说明书中述及。
Caterpillar Information System:
C4.4 (Mech) Marine Generator Set MCS-3 Manual Stop Procedure
C4.4 (Mech) Marine Generator Set MCS-3 Emergency Stopping
G3304B and G3306B Engines Engine Speed/Timing Sensor
C4.4 (Mech) Marine Generator Set MCS-3 Stopping the Engine
C4.4 (Mech) Marine Generator Set MCS-3 Fuel Conservation Practices
C4.4 (Mech) Marine Generator Set MCS-3 Engine Operation
C4.4 (Mech) Marine Generator Set MCS-3 Starting the Engine
C4.4 (Mech) Marine Generator Set MCS-3 After Starting Engine
C4.4 (Mech) Marine Generator Set MCS-3 Starting with Jump Start Cables
C4.4 (Mech) Marine Generator Set MCS-3 Cold Weather Starting
C4.4 (Mech) Marine Generator Set MCS-3 Before Starting Engine
C4.4 (Mech) Marine Generator Set MCS-3 Voltage Regulators
C4.4 (Mech) Marine Generator Set MCS-3 Fuel and the Effect from Cold Weather
C4.4 (Mech) Marine Generator Set MCS-3 Fuel Related Components in Cold Weather
C4.4 (Mech) Marine Generator Set MCS-3 Generator Operation
C4.4 (Mech) Marine Generator Set MCS-3 Single Unit Operation
C4.4 (Mech) Marine Generator Set MCS-3 Parallel Operation
C4.4 (Mech) Marine Generator Set MCS-3 Product Storage
C4.4 (Mech) Marine Generator Set MCS-3 Control Panel
C13, C15, and C18 Tier 4 Interim Engines Sensor Signal (Analog, Passive) - Test
C4.4 (Mech) Marine Generator Set MCS-3 System Pressure Release
C4.4 (Mech) Marine Generator Set MCS-3 Refill Capacities and Recommendations
C4.4 (Mech) Marine Generator Set MCS-3 Diagnostic Lamp
Replacement of Horn On Certain EMCP 3 Control Panels On Certain Generator Sets{4490, 7402} Replacement of Horn On Certain EMCP 3 Control Panels On Certain Generator Sets{4490, 7402}