Engine Oil Filter Base
Show/hide table
 | |
| 图 1 | g02112693 |
发动机机油滤清器座 | |
(1) 4N-8150 弹簧
- 数量 ... 2
- 在试验力下的长度 ... 55.24 mm (2.1750 in)
- 试验力 ... 75.619 ± 5.8 N (17 ± 1.30 lb)
- 试验后的自由长度 ... 93.726 mm (3.6810 in)
- 外径 ... 20.6 mm (0.81 in)
- 在试验力下的长度 ... 55.24 mm (2.1750 in)
机油冷却器旁通阀和机油滤清器旁通阀在 240 ± 20 kPa (35.0 ± 3.0 psi) 的压差下必须打开。
(2) 148-8406 螺塞组件 的扭矩 ... 203.5 ± 13.5 N·m (150 ± 10 lb ft)
(3) 空心螺柱的扭矩 ... 68 ± 7 N·m (50 ± 5 lb ft)
(4) 183-7262 螺塞组件 的扭矩 ... 215.5 ± 15.5 N·m (159 ± 11 lb ft)
(5) 用清洁未使用的发动机机油润滑机油滤清器密封。 在密封与底座接触后转动一圈。
注: 用 6V-6640 密封胶 涂抹空心螺柱螺纹顶部 11.0 ± 2.0 mm (0.43 ± 0.08 in) 处。
Caterpillar Information System:
C27 Generator Set Engines Air Lines
349F and 352F Excavators Hydraulic System Oil Filter (Pilot) - Replace
C18 Generator Set Electronic Modular Control Panel 3 (EMCP 3)
349F and 352F Excavators Hydraulic System Oil Filter (Case Drain) - Replace
C280-16 Petroleum Engine Temperature Sensor
797F and 797F XQ Off-Highway Trucks Machine Systems Air Tank (Primary) - Remove and Install
Procedure to Install the 353-6981 Drive Coupling Assembly on Some G3500 Engines{5510} Procedure to Install the 353-6981 Drive Coupling Assembly on Some G3500 Engines{5510}
3512E Tier 4 Final Engines for Land Electric Drilling Turbocharger Speed Sensor
797F Off-Highway Truck Power Train Torque Converter - Remove and Install
The Voltage Adjust Potentiometer Is Incorrectly Wired on Certain Generator Sets{4467, 4490, 5721} The Voltage Adjust Potentiometer Is Incorrectly Wired on Certain Generator Sets{4467, 4490, 5721}
C4.4 Industrial Engine Belt Tensioner - Inspect
EMCP4.1/EMCP4.2 Typical Generator Abbreviations
349F and 352F Excavators Hydraulic System Main Hydraulic Pump Air - Purge
349F and 352F Excavators Hydraulic System Oil - Change
C15 and C18 Petroleum Generator Sets Generator Bearing - Inspect
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator Bearing - Replace - SR5 Generator Bearings
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
2010/03/02 New Settings Are Now Used For EMCP 3 On Certain Generator Sets {4490}
G3500 Generator Sets Additional Messages
G3512E Generator Set Engine Fuel Metering Valve - Test
C7.1 Industrial Engine and Generator Set Ether Starting Aid - Test
G3500 Generator Sets Model View Illustrations
2010/08/17 New Turbochargers Are Used on Some C18 Industrial Engines {1052, 1053}
C27 and C32 Engines for Caterpillar Built Machines Camshaft