Torque Converter - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-9203     | 操纵杆滚轮举倾机构     | 3     |
B     | 138-7574     | 连杆支架     | 4     |
开始:
- 拆下主驱动轴组件。
- 将变矩器中的油排放到适当的容器中,以便存放或处理。 参阅操作和保养手册, "变矩器和变速箱油 - 更换"。
- 拆下盘 (1) 。
Show/hide table
图 1 | g02111762 |
- 将工具 (A) 、工具 (B) 和适当的的起吊设备连接到护罩组件 (2) 的后部。 护罩组件 (2) 的重量约为 272 kg (600 lb)。
Show/hide table
图 2 | g02111763 |
Show/hide table
图 3 | g02111797 |
- 将工具 (A) 、工具 (B) 和适当的的起吊设备连接到护罩组件 (2) 的前部。 护罩组件 (2) 的重量约为 272 kg (600 lb)。
Show/hide table
图 4 | g02111783 |
- 拆下螺栓 (3 ) 。 拆下防护罩组件 (2) 。
Show/hide table
图 5 | g02111777 |
Show/hide table
图 6 | g02111832 |
- 断开软管组件 (4) 。
Show/hide table
图 7 | g02114641 |
- 断开软管组件 (5) 和软管组件 (6) 。
Show/hide table
图 8 | g02115378 |
- 断开管组件 (7) 和管组件 (8) 。
Show/hide table
图 9 | g02115638 |
- 断开软管组件 (9) 。
Show/hide table
图 10 | g02111824 |
- 断开软管组件 (10) 。
Show/hide table
图 11 | g02115714 |
- 断开软管组件 (11) 。
Show/hide table
图 12 | g02111829 |
- 断开软管组件 (12) 和软管组件 (13) 。
Show/hide table
图 13 | g02111822 |
- 断开软管组件 (14) 。
Show/hide table
图 14 | g02115756 |
- 断开软管组件 (15) 。
Show/hide table
图 15 | g02116233 |
- 断开线束组件 (16) 并拆下连接紧固件。
Show/hide table
图 16 | g02115764 |
- 断开线束组件 (17) ,然后拆下连接紧固件。
Show/hide table
图 17 | g02115771 |
- 拆下辅助驱动轴护罩 (18) 。
Show/hide table
图 18 | g02116393 |
- 将工具 (A) 、工具 (B) 和适当的起吊设备连接到变矩器 (19) 上。 变矩器 (19) 的重量约为 2476 kg (5459 lb)。
Show/hide table
图 19 | g02116477 |
Show/hide table
图 20 | g02116494 |
- 拆下螺栓 (20) 。
- 拆下螺栓 (21) 。
Show/hide table
图 21 | g02116518 |
Show/hide table
图 22 | g02116553 |
- 拆下变矩器 (19) 。 拆下 O 形密封圈 (22) 。
Show/hide table
图 23 | g02116573 |
安装步骤
- 按相反顺序安装变矩器 (19) 。
- 拧紧螺栓 (20) 至 105 ± 20 N·m (77 ± 15 lb ft) 的扭矩。
Caterpillar Information System:
The Voltage Adjust Potentiometer Is Incorrectly Wired on Certain Generator Sets{4467, 4490, 5721} The Voltage Adjust Potentiometer Is Incorrectly Wired on Certain Generator Sets{4467, 4490, 5721}
C4.4 Industrial Engine Belt Tensioner - Inspect
EMCP4.1/EMCP4.2 Typical Generator Abbreviations
EMCP4.1/EMCP4.2 Electronic Control Module (Generator Set) - Flash Program
EMCP4.1/EMCP4.2 ECM Connections
G3500 Generator Sets Safety Messages
349F and 352F Excavators Hydraulic System Oil Level - Check
349F and 352F Excavators Hydraulic System Oil Sample - Obtain
349F and 352F Excavators Pump Coupling Oil - Change
797F Off-Highway Truck Power Train Drive Shaft (Main) - Remove and Install
EMCP4.1/EMCP4.2 Electronic Control Module (Generator Set) - Configure
2010/08/10 Procedure for Cleaning the Fuel Valve Gp on G3500C and G3500E Engines {1254, 1714, 5086}
3512E Tier 4 Final Engines for Land Electric Drilling Turbocharger Speed Sensor
Procedure to Install the 353-6981 Drive Coupling Assembly on Some G3500 Engines{5510} Procedure to Install the 353-6981 Drive Coupling Assembly on Some G3500 Engines{5510}
797F and 797F XQ Off-Highway Trucks Machine Systems Air Tank (Primary) - Remove and Install
C280-16 Petroleum Engine Temperature Sensor
349F and 352F Excavators Hydraulic System Oil Filter (Case Drain) - Replace
C18 Generator Set Electronic Modular Control Panel 3 (EMCP 3)
349F and 352F Excavators Hydraulic System Oil Filter (Pilot) - Replace
C27 Generator Set Engines Air Lines
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base
349F and 352F Excavators Hydraulic System Main Hydraulic Pump Air - Purge
349F and 352F Excavators Hydraulic System Oil - Change
C15 and C18 Petroleum Generator Sets Generator Bearing - Inspect