Air Tank (Primary) - Remove and Install
拆卸步骤
Show/hide table
为防止可能的人身伤害,在断开空气系统的任何部件前,释放空气箱压力。 |
- 如果配备有抑噪配置,则请参阅专门说明书, " 351-3820 抑噪配置(如有配备)的安装",了解专用面板位置和正确的拆卸或安装步骤。
- 释放空气系统压力。 请参阅操作和保养手册, "系统压力释放"。
- 断开软管组件 (1) 和软管组件 (2) 。
Show/hide table
图 1 | g02113513 |
- 将适当的起吊设备连接到气罐 (3) 上。 气罐 (3) 的重量约为 250 kg (550 lb)。
Show/hide table
图 2 | g02113582 |
- 断开软管组件 (4) 。 拆下螺栓 (5) 和安装件。
- 将工具 (A) 和适当的起吊设备连接到气罐 (3) 上。 气罐 (3) 的重量约为 250 kg (550 lb)。
Show/hide table
图 3 | g02113589 |
Show/hide table
图 4 | g02113594 |
- 拆下螺栓 (6) 。
Show/hide table
图 5 | g02113596 |
- 拆下气罐 (3) 。
Show/hide table
图 6 | g02113655 |
安装步骤
- 按与拆卸相反的顺序安装气罐 (3) 。
Caterpillar Information System:
Procedure to Install the 353-6981 Drive Coupling Assembly on Some G3500 Engines{5510} Procedure to Install the 353-6981 Drive Coupling Assembly on Some G3500 Engines{5510}
3512E Tier 4 Final Engines for Land Electric Drilling Turbocharger Speed Sensor
797F Off-Highway Truck Power Train Torque Converter - Remove and Install
The Voltage Adjust Potentiometer Is Incorrectly Wired on Certain Generator Sets{4467, 4490, 5721} The Voltage Adjust Potentiometer Is Incorrectly Wired on Certain Generator Sets{4467, 4490, 5721}
C4.4 Industrial Engine Belt Tensioner - Inspect
EMCP4.1/EMCP4.2 Typical Generator Abbreviations
EMCP4.1/EMCP4.2 Electronic Control Module (Generator Set) - Flash Program
EMCP4.1/EMCP4.2 ECM Connections
G3500 Generator Sets Safety Messages
349F and 352F Excavators Hydraulic System Oil Level - Check
349F and 352F Excavators Hydraulic System Oil Sample - Obtain
349F and 352F Excavators Pump Coupling Oil - Change
C280-16 Petroleum Engine Temperature Sensor
349F and 352F Excavators Hydraulic System Oil Filter (Case Drain) - Replace
C18 Generator Set Electronic Modular Control Panel 3 (EMCP 3)
349F and 352F Excavators Hydraulic System Oil Filter (Pilot) - Replace
C27 Generator Set Engines Air Lines
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base
349F and 352F Excavators Hydraulic System Main Hydraulic Pump Air - Purge
349F and 352F Excavators Hydraulic System Oil - Change
C15 and C18 Petroleum Generator Sets Generator Bearing - Inspect
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator Bearing - Replace - SR5 Generator Bearings
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
2010/03/02 New Settings Are Now Used For EMCP 3 On Certain Generator Sets {4490}