MID 027 - CID 0709 - FMI 06
产生此代码的情况:
Show/hide table
图 1 | g02028574 |
锁定离合器电磁阀的连接 |
该诊断代码与锁定离合器电磁阀有关。 FMI 06 表示 ECU 已确定电磁阀电路中存在对接地短路。
产生此诊断代码的可能原因如下:
- 电磁阀电源电路对接地短路。
- 电磁阀出现故障。
- ECU 有故障。 这不太可能。
注: 以下测试步骤可能会生成其他诊断代码。 忽略生成的这些诊断代码,并在修复原有诊断代码后清除这些忽略的诊断代码。 执行本步骤之前,请确保诊断代码 CID 0709 FMI 06 处于激活状态。
注: 使用数字万用表执行此步骤中的测量。
测试步骤 1. 检查电磁阀。
- 将断路开关和钥匙起动开关转到接通位置。 不要起动发动机。
- 观察诊断代码的状态。
- 将出现现行诊断代码的电磁阀从机器线束上断开。
预期结果:
电磁阀断开时,FMI 06 变为 FMI 05。
结果:
- 是 - 电磁阀断开时,FMI 06 变为 FMI 05。 电路正常。
修复: 电磁阀出现故障。 更换电磁阀。 确认使用新电磁阀后故障得到排除。
停止
- 否 - FMI 06 保持为激活状态。 转至测试步骤 2。
测试步骤 2. 检查电磁阀电源电路是否对接地短路。
- 将钥匙起动开关和断路开关转到断开位置。
- 电磁阀仍保持从机器线束上断开的状态。
- 从 ECU 上断开机器线束接头。
- 在机器线束接头上,测量信号触点 J1-62(导线 705-PK(粉))与 ECU 的机器线束接头中使用的所有触点之间的电阻。
预期结果:
各电阻测量值都大于 5000 欧姆。
结果:
- 正常 - 各电阻测量值都大于 5000 欧姆。 机器线束正常。 转至测试步骤 3。
- 异常 - 各电阻测量值都不大于 5000 欧姆。 机器线束中存在短路。 J1-62(导线 705-PK(粉))与电阻测量值低的电路之间存在短路。
修复: 修理或更换机器线束。
停止
测试步骤 3. 检查是否仍存在该诊断代码。
- 检查线束接头。 清理线束接头的触点,并检查导线绝缘层是否由于过热、蓄电池酸液或擦伤而损坏。
- 对与电路有关的每一根导线进行拉力为
45 N (10 lb) 的拉拔测试。 - 重新连接所有线束接头以便确保接头完全座入。 此外,确保各个接头的夹子紧固。
- 将断路开关和钥匙起动开关转到接通位置。
- 操作机器。
- 检查 CID 0709 FMI 06 的状态。
预期结果:
CID 0709 FMI 06 为激活状态。
结果:
- 是 - CID 0709 FMI 06 为激活状态。 尚未修复该诊断代码。
修复: ECU 不太可能会出现故障。 先退出此步骤,然后重新执行此步骤。 如果没有找到该诊断代码的原因,则应更换 ECU。 更换 ECU 之前,务必先咨询当地代理商的技术通信员征求 Caterpillar 可能的意见。 此咨询可以大大降低维修时间。 有关更多信息,请参阅测试和调整, KENR8291, "电子控制单元 - 更换"。
停止
- 否 - CID 0709 FMI 06 为未激活状态。 此时不存在该故障。
修复: 原有诊断代码可能是某个断开以及重新连接的线束接头上存在接触不良或短路引起的。 使机器恢复正常运转。
停止
Caterpillar Information System:
797F and 797F XQ Off-Highway Truck Braking System Gear Motor (Rear Axle Oil Cooler Fan)
G3500 Generator Sets Product Lifting
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0709 - FMI 05
2009/09/14 Installing the Cross Bolts for the Main Bearings in C27 and C32 Engines {1201}
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0709 - FMI 03
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 08
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 04
3000 Frame SR5 Electric Power Generation Front Bracket - Remove and Install
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 03
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0673 - FMI 08
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0673 - FMI 02
C15 and C18 Engines for Caterpillar Built Machines Fuel Transfer Pump
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0826 - FMI 03
G3500 Generator Sets Electronic Modular Control Panel II+ (EMCP II+)
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0826 - FMI 04
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1248 - FMI 03
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1248 - FMI 05
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1248 - FMI 06
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1292 - FMI 04
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1401 - FMI 03
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1401 - FMI 05
C7.1 Industrial Engine and Generator Set Customer Specified Parameters
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1401 - FMI 06