Piston Cooling Jets - Remove and Install
Start By:
- Remove the engine oil pump, if necessary. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove the cylinder block cover from the side of the engine.
Show/hide table
Illustration 1 g00913178 Show/hide table
Illustration 2 g00913185 - Remove bolts (1) and retainer (2).
- Remove piston cooling jet (3) from the inside of the engine.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position piston cooling jet (3) in the engine block. Ensure that the oil holes in the end of the jet are facing toward the piston.
Note: Handle the cooling jet with care to prevent damage to the piston.
- Install retainer (2) and bolts (1).
- Install the cylinder block cover on the side of the engine.
Show/hide table
| |
| Illustration 3 | g00913185 |
Show/hide table
| |
| Illustration 4 | g00913178 |
End By:
- Install the engine oil pump, if necessary. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar Information System:
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Cylinder Head - Remove
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Cylinder Head - Install
G3508J, G3516J, and G3520J Engines Nitrogen Oxide Sensor - Remove and Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Rocker Shaft and Push Rod - Install
Wiring Improvements For The Contactor On The Control Group For Jacket Water Heaters, Space Heaters, And Some Battery Chargers On The 3412C, The 3406C, The 3456C, The C9, The C15, And The C18 Generator Sets{1435} Wiring Improvements For The Contactor On The Control Group For Jacket Water Heaters, Space Heaters, And Some Battery Chargers On The 3412C, The 3406C, The 3456C, The C9, The C15, And The C18 Generator Sets{1435}
2009/01/12 Adding Heat Shrink To The Harness Reduces Warnings {1273, 1408}
G3516 Petroleum Engines Valve Cover and Spark Plug - Remove and Install
G3500B Engines Air/Fuel Ratio Problem
797F and 797F XQ Off-Highway Truck/Tractor Braking System Electronic Control Module (Brake)
797F and 797F XQ Off-Highway Truck/Tractor Braking System Brake Hydraulic System
2009/01/26 Final Drive Duo-Cone Seal Assembly Information Update {7561}
3600 and C280 Diesel Engine Fluids Recommendations Biodiesel
Cat Commercial Diesel Engine Fluids Recommendations Coolant Recommendations - General Maintenance
C18 Fire Pump Engine Belts - Inspect/Adjust/Replace
793F Off-Highway Truck Towing With Inoperable Engine
C175-16 and C175-20 Generator Set Engines Oil Contains Coolant
C6.6 Marine Generator Set Engine Crankcase Breather - Replace
G3516 Petroleum Engines Connecting Rod Bearings - Remove and Install
PM3516 Power Modules Configuration Parameters
G3516 Petroleum Engines Piston and Connecting Rods - Remove
G3516 Petroleum Engines Piston and Connecting Rods - Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Camshaft - Remove
C6.6 Marine Generator Set Engine Oil Pressure
G3516 Petroleum Engines Crankshaft Main Bearings - Remove