Cylinder Head - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 4 |
Start By:
- Remove the rocker shaft assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Push Rod - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Note: Repeat the procedure for each cylinder head.
- Drain the coolant from the cooling system into a suitable container for storage or disposal.
Show/hide table
Illustration 1 g00759319 - Remove the bolts that fasten bracket (1) to the water manifold.
- Remove the bolts from the valve cover base (2). Remove valve cover base (2) from the cylinder head.
Show/hide table
Illustration 2 g00760142 - Remove exhaust temperature sensor (3) from the cylinder head.
Show/hide table
Illustration 3 g00760018 - Remove the bolts from air inlet elbow (5). Remove gasket (7).
- Remove the bolts and tube (4) . Remove gaskets (6).
Show/hide table
Illustration 4 g00760271 Typical example - Remove the bolts from exhaust elbow (9). Remove gasket (8).
Show/hide table
Illustration 5 g00760306 - Install Tooling (A) on cylinder head (11). Use the holes for the bolts that hold the valve cover base.
- Fasten a suitable lifting device to cylinder head (11).
- Remove bolts (10) and bolts (12) from cylinder head (11).
- Remove cylinder head (11) from the engine. The weight of cylinder head (11) is approximately
47 kg (105 lb) .Show/hide tableIllustration 6 g00760369 - Remove cylinder head gasket (16), four seals (13), four seals (14), and O-ring seal (15) from the spacer plate.
- Remove spacer plate (17).
Show/hide table
Illustration 7 g00760395 - Remove spacer plate gasket (18) from the dowels.
- Remove O-ring seal (19) from the dowel.
Caterpillar Information System:
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Cylinder Head - Install
G3508J, G3516J, and G3520J Engines Nitrogen Oxide Sensor - Remove and Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Rocker Shaft and Push Rod - Install
Wiring Improvements For The Contactor On The Control Group For Jacket Water Heaters, Space Heaters, And Some Battery Chargers On The 3412C, The 3406C, The 3456C, The C9, The C15, And The C18 Generator Sets{1435} Wiring Improvements For The Contactor On The Control Group For Jacket Water Heaters, Space Heaters, And Some Battery Chargers On The 3412C, The 3406C, The 3456C, The C9, The C15, And The C18 Generator Sets{1435}
2009/01/12 Adding Heat Shrink To The Harness Reduces Warnings {1273, 1408}
G3516 Petroleum Engines Valve Cover and Spark Plug - Remove and Install
G3500B Engines Air/Fuel Ratio Problem
797F and 797F XQ Off-Highway Truck/Tractor Braking System Electronic Control Module (Brake)
797F and 797F XQ Off-Highway Truck/Tractor Braking System Brake Hydraulic System
2009/01/26 Final Drive Duo-Cone Seal Assembly Information Update {7561}
3600 and C280 Diesel Engine Fluids Recommendations Biodiesel
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Flywheel Housing - Install
G3516 Petroleum Engines Piston Cooling Jets - Remove and Install
Cat Commercial Diesel Engine Fluids Recommendations Coolant Recommendations - General Maintenance
C18 Fire Pump Engine Belts - Inspect/Adjust/Replace
793F Off-Highway Truck Towing With Inoperable Engine
C175-16 and C175-20 Generator Set Engines Oil Contains Coolant
C6.6 Marine Generator Set Engine Crankcase Breather - Replace
G3516 Petroleum Engines Connecting Rod Bearings - Remove and Install
PM3516 Power Modules Configuration Parameters
G3516 Petroleum Engines Piston and Connecting Rods - Remove
G3516 Petroleum Engines Piston and Connecting Rods - Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Camshaft - Remove
C6.6 Marine Generator Set Engine Oil Pressure