Main Hydraulic Pump and Pump Drive Coupling - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 140-7742     | 套筒     | 1     |
B     | 138-7573     | 连杆支架     | 2     |
开始:
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
- 拆下消音器。 请参阅拆解和组装, "消音器 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
注: 在所有管路、软管、导线和管子上做出识别标记以便安装。 插接所有管路、软管和管子。 这将有助于防止液体泄漏和防止污染物进入系统。
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 将液压油箱中的油排入合适的容器以便保存或废弃这些油。 请参阅操作和保养手册, "液压系统机油 - 更换"。
- 拆下支撑 (1) 。
Show/hide table
图 1 | g01759777 |
- 拆下支架 (2) 和盖 (3) 。
Show/hide table
图 2 | g01759793 |
- 将盖 (4) 作为一个单元拆下。
Show/hide table
图 3 | g01759796 |
- 将工具 (A) 和适当的起吊设备连接在支承 (5) 上。 支承 (5) 的重量约为 43 kg (95 lb)。
Show/hide table
图 4 | g01759840 |
- 拆下护罩 (6) 。
Show/hide table
图 5 | g01759853 |
- 将线束组件 (7) 从主液压泵和盖 (8) 上断开。 重新定位线束组件 (7) 。 拆下盖 (8) 。
Show/hide table
图 6 | g01759935 |
- 将所有软管组件 (10) 从主液压泵 (9) 上断开。 断开管组件 (11) 。
Show/hide table
图 7 | g01760633 |
- 断开软管组件 (12) 和 (13) 。
Show/hide table
图 8 | g01760635 |
Show/hide table
图 9 | g01760233 |
- 拆下盖 (14) 。
Show/hide table
图 10 | g01760637 |
- 将工具 (B) 和适当的起吊设备连接到主液压泵 (9) 上。 主液压泵 (9) 的重量约为 318 kg (700 lb)。 拆下螺栓 (15) 。 拆下主液压泵 (9) 。
Show/hide table
图 11 | g01760817 |
Show/hide table
图 12 | g01760733 |
- 拆下螺栓 (16) 和连接组件 (17) 。
Show/hide table
图 13 | g01760886 |
Caterpillar Information System:
2008/11/01 Policy on Testing of Fuel Injectors and Fuel Nozzles {1251}
2008/11/17 Policy on Testing of Fuel Injectors and Fuel Nozzles {1251}
2008/11/17 Policy on Testing of Fuel Injectors and Fuel Nozzles {1251}
2008/12/01 New Primary Fuel Filter {1258, 1261, 1263}
G3500B Engines Diagnostic Trouble Codes
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Gear Pump (Pilot) - Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Gear Pump (Pilot) - Remove
G3500B Engines Troubleshooting Data Sheet
C6.6 Marine Generator Set EMCP3 General Information
C6.6 Marine Generator Set Jacket Water Heater - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Fan Pump - Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Fan Pump - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Main Hydraulic Pump and Pump Drive Coupling - Install
G3500B Engines Configuration Parameters
G3500B Engines Camshaft
793F and 797F Off-Highway Trucks Chassis Electronic Control System System Schematic
2008/12/01 Water Temperature Regulator {1355, 1380}
G3520C and G3520E Generator Set Engines Vibration Damper - Disassemble
2008/11/17 Do Not Use the 6V-4022 Fuel Injector Tester to Measure Unit Injector Fuel Flow Rate {1251, 1254, 1290, 1713}
G3520C and G3520E Generator Set Engines Vibration Damper - Assemble
G3520C and G3520E Generator Set Engines Vibration Damper - Remove
2008/11/17 The 6V-4022 Fuel Injector Tester Is not Available {1251, 1254, 1290, 1713}
TH48-E70 Petroleum Transmission and TH48-E70-C27I, TH48-E70-C32I and TH48-E70-C32P Petroleum Power Train Packages Speed Sensor (Transmission) - Engine Output
2008/11/17 The 6V-4022 Fuel Injector Tester Is not Available {1251, 1254, 1290, 1713}