Aftercooler - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Guide Stud M8 - 1.25 by 100 mm |
2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tooling (A) at Locations (X). Install the gasket on Tooling (A).
- Attach a suitable lifting device to aftercooler (8). The weight of aftercooler (8) is approximately
35 kg (77 lb) . - Position aftercooler (8) on the engine and install bolts (4). Remove Tooling (A) and install the remaining bolts. Tighten the bolts according to the numerical sequence that is shown in Illustration 2. Tighten the bolts to a torque of
31 ± 3 N·m (23 ± 2 lb ft) . - Connect harness assembly (3) and harness assembly (2).
- Install bracket (9). Connect tube (10) to aftercooler (8).
- Connect hose (11) to aftercooler (8).
- Install tube assembly (1) on the engine.
- Connect tube assembly (6) to aftercooler (8). Install the retainers and bolts (7).
- Reposition the bracket for the air inlet heater solenoid and install bolts (5).
- Install the hose assemblies on the unit injector hydraulic pump and the fuel transfer pump, if necessary.
- Fill the aftercooler with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
| |
| Illustration 1 | g01465869 |
Show/hide table
| |
| Illustration 2 | g01466368 |
Caterpillar Information System:
C175-16 and C175-20 Generator Set Engines Fuel Filter Is Restricted
C175-16 and C175-20 Generator Set Engines Engine Overspeeds
C7 PETROLEUM Petroleum Engine Aftercooler - Remove
2008/03/03 A New Oil Filter Group is Now Used on the TH48-E80 Oil/Gas Transmission {3030, 3067}
C15 Industrial Engines Configuration Parameters
CX28 On-Highway Transmission Output Transfer Yoke
C175-16 and C175-20 Generator Set Engines Engine Does Not Crank
2008/05/01 A New Version of Caterpillar Electronic Technician (ET) is Now Available {0785, 1900, 7610}
2008/05/26 A New Version of Caterpillar Electronic Technician (ET) is Now Available {0785, 1900, 7610}
2008/05/19 A New Version of Caterpillar Electronic Technician (ET) is Now Available {0785, 7600, 7610}
C7 PETROLEUM Petroleum Engine Air Lines - Remove and Install
C175-16 Locomotive Engines Fuel System Primary Filter/Water Separator - Drain
C175-16 and C175-20 Generator Set Engines Fuel Pressure Is Low - Fuel Supply System
C175-16 and C175-20 Generator Set Engines Inlet Air Is Restricted
C7 PETROLEUM Petroleum Engine Air Inlet Heater - Remove and Install
C9T-TH31 Petroleum Package Walk-Around Inspection
C11, C13, and C15 On-highway Engines Reference Material
2008/03/01 Visible Indication for Engagement of the Electrical Connector has Been Added to the Ignition Coil for the Caterpillar Regeneration System (CRS) {108B}
SR5 Electric Power Generation Diode Assembly - Remove and Install
C175-16 Locomotive Engine Exhaust Manifold
C175-16 and C175-20 Generator Set Engines Component Location
3500 Industrial Engines Exhaust Flange
C15 On-Highway Engine Combustion Head Group (ARD) - Remove and Install - Heated Nozzle
Bench Test Procedure for TH55FT - E70 and TH55FT - E90 Oil Field Transmission{3030, 3167} Bench Test Procedure for TH55FT - E70 and TH55FT - E90 Oil Field Transmission{3030, 3167}