Camshaft
Show/hide table
Illustration 1 | g01431451 |
(1) Exhaust lobe (2) Injector lobe (3) Inlet lobe (5) Front of camshaft |
Note: Lubricate the camshaft lobes with a 50/50 mixture of 8T-2998 Lubricant and clean engine oil.
(4) Bearing journal
- Diameter of the bearing journals ... 84.85 ± 0.02 mm (3.341 ± 0.001 inch)
Note: Lubricate the camshaft bearings with clean engine oil prior to installing the camshaft.
Show/hide table
Illustration 2 | g01431453 |
(B) Camshaft lobe height (C) Base circle |
(A) Camshaft lobe lift
-
Specified camshaft lobe lift
- Exhaust lobe ... 8.515 mm (0.3352 inch)
- Inlet lobe ... 9.702 mm (0.3820 inch)
- Injector lobe ... 10.451 mm (0.4115 inch)
- Inlet lobe ... 9.702 mm (0.3820 inch)
To find the lobe lift, use the procedure that follows:
- Measure camshaft lobe height (B) .
- Measure base circle (C) .
- Subtract the base circle measurement (Step 2) from the camshaft lobe height (Step 1). The difference is the actual lobe lift.
Maximum permissible difference between the actual lobe lift and the specified lobe lift of a new camshaft ... 0.13 mm (0.005 inch)
Show/hide table
Illustration 3 | g01431454 |
(9) Bolt
- Tighten the bolts that fasten the cover to the cylinder head to the following torque. ... 13 ± 3 N·m (10 ± 2 lb ft)
Caterpillar Information System:
C18 Marine Generator Set Engine Shutoffs and Engine Alarms
C12 Marine Engines Engine Oil Pan
3512B and 3516B High Displacement Locomotive Engines Overhaul (Major)
3512B and 3516B High Displacement Locomotive Engines Overhaul (Top End)
C27 and C32 Generator Sets Overhaul Considerations
3176C, 3406E and 3456 Industrial Engines Ether Starting Aid - Test
G3600 Engines Sensor Signal (Analog, Active) - Test
G3600 Engines Coolant Temperature Is High
C7 and C9 On-highway Engines Configuration Parameters - Customer Specified Parameters
3176C, 3406E and 3456 Industrial Engines Injector Solenoid - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Glow Plugs - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Glow Plugs
G3600 Engines Sensor Signal (Analog, Passive) - Test
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Air Shutoff - Test
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Event Codes
Procedure to Prevent or Correct Multi-Station Control System (MSCS) Throttle Issues{1901, 1915, 3065, 5910} Procedure to Prevent or Correct Multi-Station Control System (MSCS) Throttle Issues{1901, 1915, 3065, 5910}
C13 and C15 On-Highway Engines Configuration Parameters - Customer Specified Parameters
3406E and C15 Marine Engines Engine Oil Pan
3406E and C15 Marine Engines Engine Oil Pan
G3600 Engines Sensor Supply - Test
2007/11/19 A New Water Seal and a New Spacer are Used for the Water Pumps {1361, 1361}
3176C, 3406E and 3456 Industrial Engines Data Link - Test
797F Off-Highway Truck Power Train Relief Valve (Transmission Lubrication) - Disassemble
2007/11/12 Use the Turbocharger Seal Kit to Repair Exhaust Leaks {1052, 1053, 7555}