Procedure to Install the Bluetooth Receiver Kit on Certain 320 GC, 330 GC, 336 GC and 345 GC Excavators {7008} Caterpillar

Excavator

320 GC (S/N: BR41-UP; DKJ1-UP; KTN1-UP; ZBT1-UP)

330 GC (S/N: NDH1-UP; FEK1-UP; GDW1-UP)

336 GC (S/N: GSF1-UP; EBJ1-UP; HFJ1-UP; JFW1-UP)

345 GC (S/N: KEF1-UP)

Introduction

This Special Instructions contains the procedure to install the Bluetooth Receiver kit on the machines listed above.

Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.

Caterpillar Channel 1 Videos

For information on Visual Service Procedures (VSP), refer to the following video. The previous training has been replaced with the video below.

Note: A CWS login is required to access Caterpillar Channel 1. Scan the QR code below with a QR enabled device or copy the link that follows.

Illustration 1	g06306276

Reference: Systems Operation, Testing and Adjusting, Troubleshooting, M0083909, "Bluetooth Operator ID and Machine Security System (MSS)"

Safety Section

Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.

A person must be alert to potential hazards. This person must also have the necessary training, skills, and tools to perform these functions properly.

Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance of a potential hazard.

Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Avoid using a tool, a procedure, a work method, or operating technique that is not recommended by Caterpillar. If used, ensure the safety of the operating personnel and others.

Ensure that the product will not be damaged or the product will be made unsafe by the operation, lubrication, maintenance, or the repair procedures.

Operation and maintenance of the machine must not occur unless the instructions and warnings in the machines Operation and Maintenance Manual have been read and are understood.

Show/hide table

Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.

General Information

Graphic Color Description

Color-coding of targeted components, or sections of a part, is used to communicate a required action.

This table shows the different colors and what is represented when used in a graphic.

(Blue) The primary component of focus for a particular step. Target or primary component to be installed or removed. Installation implied unless otherwise noted with a symbol.

(CAT® Yellow) Description of parts.

(Yellow) Components placed aside for access, but not removed. Highlighted areas of adjustment, inspection, or special attention.

(Cyan) Special tools or other equipment required for use in a particular step.

(Light Gray) Components used for reference.

(Magenta) Any fastener, retainer, or electrical connector used to install or remove the primary component.

Graphic Symbol Description

This section includes all the symbol graphics used throughout the Visual Service Procedure (VSP), along with a brief description of what the symbol represents.

Attach - To connect together or to fasten on something.

Connect - To place in an electrical circuit. To join or fasten together.

Discard, Do Not Reuse - To cast aside as useless or undesirable in approved and responsible manner.

Level - To position a surface in a horizontal orientation. To position in vertical dimension. To align to assist positioning a surface in a horizontal orientation.

Position - To locate to the desired or intended location.

Remove - To take off.

Tighten - To make nearer, to fully stretch, without slack, or to apply tension or torque.

Required Parts

Illustration 2	g06237804

Machine Preparation

Illustration 3	g06142856

Installation Procedure

Illustration 4	g06237813

Illustration 5	g06237826