The Engine Oil Filter Group is Improved on Certain 627K and 637K Wheel Tractor Scrapers {1306, 1308}
- Wheel Tractor-Scraper
- 627K (S/N: WTC264-UP; WTN115-UP)
- 637K (S/N: WTS115-UP; WTT102-UP; WTX101-UP; WTY100-UP)
Description Of Change: The engine oil filter group is improved on the rear scraper engine of machines listed above. Engine oil filter group is improved with the plunger relief valve to avoid oil bypass during the machine normal operating condition. The addition of these parts improves the filtering efficiency of the filter assembly by adjusting the oil bypass rate.
The following changes are effective with all products after the listed serial numbers.
Show/hide table
Illustration 1 | g06226805 |
Show/hide table
Required Parts | |||
Item | Qty | Part Number | Description |
1 | 1 | Valve Plunger | |
2 | 1 | Spring | |
3 | 1 | O-Ring Seal |
New 392-9208 Valve Plunger, 4N-8150 Spring, and 7M-8485 O-Ring Seal are part of 386-9385 Engine Oil Filter Gp and 465-0950 Engine Oil Filter Gp in the installation arrangement.
Installation Procedure
- Remove plug assembly (A) from the bypass valve port.
Show/hide table
Illustration 3 g06225642 View of area B
(1)392-9208 Valve Plunger
(2)4N-8150 Spring
(3)7M-8485 O-Ring Seal - Install valve plunger (1) into the bypass valve port. Refer to Illustration 3 for proper orientation to install the valve plunger (1).
- Install spring (2) into the open end of the valve plunger (1) as shown in Illustration 3.
Note: O-Ring seal (3) on the plug assembly (A) can be replaced, if required.
- Install Plug assembly (A) into the bypass valve port as shown in Illustration 3.
Show/hide table
Illustration 2 | g06225645 |
(A) Plug assembly |
Caterpillar Information System:
C9.3B Engines for Caterpillar Built Machines Belt Tensioner - Remove and Install
MD6200 Rotary Drill Fuses - Replace
C9.3B Engines for Caterpillar Built Machines Inlet Manifold Pressure Sensor - Remove and Install
Next Generation Hydraulic Excavator Monitoring System Prestart Monitoring Function
A New Spacers in the Steering Cylinder Group Are Now Used on Certain Wheel Skidders {4303} A New Spacers in the Steering Cylinder Group Are Now Used on Certain Wheel Skidders {4303}
330 GC and 330 Excavator Diesel Exhaust Fluid Injector - Replace - C7.1 Engine
990K Wheel Loader Systems Exhaust Lines
990K Wheel Loader Systems Final Drive and Wheel
AD22 Underground Articulated Truck Braking System Brake Cooling Pressure - Check
AD22 Underground Articulated Truck Braking System Brake Disc Wear - Check
AD22 Underground Articulated Truck Braking System Braking System Air - Purge
336 and 336 GC Excavator Maintenance Interval Schedule
854K Wheel Dozer Systems Hydraulic Tank and Mounting
854K Wheel Dozer Systems Oil Filter (Case Drain)
854K Wheel Dozer Systems Oil Filter (Hydraulic) - Fan
844K Wheel Dozer Systems Lift Cylinder
D9R Track-Type Tractor Systems Bulldozer Tilt Cylinder
986K Wheel Loader Systems Oil Filter (Hydraulic) - Pilot Lines
D9R Track-Type Tractor Systems Bulldozer Tilt Cylinder
844K Wheel Dozer Systems Steering Control
A Turbocharger Inlet Hose Heat Shield Is Now Used on Certain 930K and 938K Wheel Loaders {1067, 1071} A Turbocharger Inlet Hose Heat Shield Is Now Used on Certain 930K and 938K Wheel Loaders {1067, 1071}
MD6250 Rotary Drill Systems Location of Components
320, 323 Excavator Engine Supplement Fuel Filter and Base - Remove and Install
Inertial Measurement Unit (IMU) Sensors are Now Isolation Mounted on Certain 631K and 637K Wheel Tractor-Scrapers {1408, 1439} Inertial Measurement Unit (IMU) Sensors are Now Isolation Mounted on Certain 631K and 637K Wheel Tractor-Scrapers {1408, 1439}