Electrical Connectors
Connectors for the Electronic Control Module (ECM)
The Electronic Control Module (ECM) uses connectors that have 70 terminals to interface to the wiring harness.
Show/hide table
| |
| Illustration 1 | g01877659 |
|
Layout of the Connector Pins (view from the rear) | |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 151-6320 | Removal Tool (Red) | 1 |
Show/hide table
| |
| Illustration 2 | g01877813 |
|
Removal Tool | |
- Remove the connector from the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
- Position Tooling (A) around wire (2).
Note: Make sure that the tool stays perpendicular to the face of connector (1).
- Push the tool into the hole for the terminal. Gently pull the wire to remove the terminal from the rear of connector (1).
- Remove the Tooling (A) from the wire.
Note: If a terminal must be replaced, part number 9X-3402 must be used for 16 and 18 AWG wire. Part number 126-1768 must be used for 14 AWG wire.
- Push the terminal into the rear of connector (1) until the terminal engages with the locking device.
- Gently pull on wire (2) to make sure that the terminal is retained by the locking device.
- Connect the connector to the ECM and then tighten the retaining screw to a torque of
6 N·m (53 lb in) .
Show/hide table
| |
| Illustration 3 | g06099709 |
Analog Sensor Connector (active)
Show/hide table
| |
| Illustration 4 | g01240891 |
Analog Sensor Connector (passive)
Show/hide table
| |
| Illustration 5 | g01241538 |
Connectors for the Termination Resistor
Show/hide table
| |
| Illustration 6 | g01355248 |
Show/hide table
| |
| Illustration 7 | g01155187 |
Show/hide table
| |
| Illustration 8 | g02219254 |
Show/hide table
| |
| Illustration 9 | g02220494 |
Caterpillar Information System:
Cab Pressurizer Now Available as a Group for Underground Articulated Trucks and Load Haul Dump Machines {7311} Cab Pressurizer Now Available as a Group for Underground Articulated Trucks and Load Haul Dump Machines {7311}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Diesel Particulate Filter Regeneration Does Not Occur
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Hydraulic Fan Speed - Test and Adjust
950 GC Wheel Loader Automatic Lubrication System - If Equipped
D11 Main Frame Inspection and Weld Repair Procedure {0679, 7051} D11 Main Frame Inspection and Weld Repair Procedure {0679, 7051}
992K Wheel Loader Plate Locations and Film Locations
Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000} Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000}
854K Wheel Dozer Windows - Clean
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control - Control System
340F Excavator Machine Systems Relief Valve (Pilot) - Test and Adjust
340F Excavator Machine Systems Pump Control (Output Flow) - Test - One Pump Calibration (Optional Test)
C4.4 and C6.6 Engines Event Codes
631K OEM Power Train Speed Sensor (Transmission) - Remove and Install - Tractor
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Oil Pump
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Magnetic Screen
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Lubrication
973K Track Type Loader Engine Oil Level - Check
973K Track Type Loader Engine Oil Sample - Obtain
Product Evaluation Report - AFA Bad Report {0374, 1000} Product Evaluation Report - AFA Bad Report {0374, 1000}
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Output Transfer Gears
973K Track Type Loader Engine Oil and Filter - Change
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Fixed Axle (Front) and Oscillating Axle (Rear)
C4.4 and C6.6 Engines Acceleration Is Poor or Throttle Response Is Poor