Engine Oil Filter and Base - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 185-3630 | Strap Wrench As | 1 |
B | - | LOCTITE 263 | - |
- | LOCTITE 270(1) | - |
Show/hide table
(1) | Europe Only |
Start By:
- Remove the left side engine enclosure.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Use Tooling (A) to remove engine oil filter (3).
- Remove bolts (2), base (1), and the gasket.
Show/hide table
Illustration 2 g06056224 - Remove stud (4) from filter base (1).
Show/hide table
Illustration 1 | g06056243 |
- Install engine oil filter (3) and base (1) in the reverse order of removal
- Tighten bolts (2) to a torque of
22 N·m (16 lb ft) - Before fitting the stud (4), apply Tooling (B) around the circumference of the connector. Tighten the stud (4) into filter base to a torque of
35 ± 5 N·m (26 ± 4 lb ft) .
- Tighten bolts (2) to a torque of
Caterpillar Information System:
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine Electronic Control System General Information
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine Electronic Control System Transmission
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loader Machine Systems Piston Pump (Hydrostatic) - Disassemble
C4.4 (Mech) Industrial Engine Crankshaft - Spheroidal Graphite Iron (SGI) Crankshaft
815K Soil Compactor and 816K Landfill Compactor Oil Filter (Hydraulic)
525D, 535D, 545D and 555D Wheel Skidders Power Train Axle Housing - Disassemble
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Circuit Breaker (Powered Stairway)
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Circuit Breaker (Alarm)
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Circuit Breakers
Front and Rear Axle Lip Seal May Fail on Certain M-Series Medium Wheel Loaders {3254, 3256, 3258, 3282, 7555} Front and Rear Axle Lip Seal May Fail on Certain M-Series Medium Wheel Loaders {3254, 3256, 3258, 3282, 7555}
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Hydraulic Cylinder (Powered Stairway)
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Relief Valve (Ladder Position)
Installation of the 508-1863 Air Conditioner and Heater Installation Kit on Certain Compact Track Loaders and Skid Steer Loaders {1405, 1802, 1805, 1808, 7174, 7304, 7320, 734D} Installation of the 508-1863 Air Conditioner and Heater Installation Kit on Certain Compact Track Loaders and Skid Steer Loaders {1405, 1802, 1805, 1808, 7174, 7304, 7320, 734D}
3512E Tier 4 Final Engines for Land Electric Drilling Fuel Consumption Is Excessive
Installation of the 509-5548 Cab Heater and Mounting Kit on Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {1812, 7304, 7309, 734D} Installation of the 509-5548 Cab Heater and Mounting Kit on Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {1812, 7304, 7309, 734D}
3512E Tier 4 Final Engines for Land Electric Drilling Power Is Intermittently Low or Power Cutout Is Intermittent
3512E Tier 4 Final Engines for Land Electric Drilling Engine Top Speed Is Not Obtained
3512E Tier 4 Final Engines for Land Electric Drilling Engine Stalls at Low RPM
3512E Tier 4 Final Engines for Land Electric Drilling Acceleration Is Poor or Throttle Response Is Poor
AD22 Underground Articulated Truck Light Switches
C4.4 (Mech) Industrial Engine Main Bearing Journal - Spheroidal Graphite Iron (SGI) Crankshaft
C4.4 (Mech) Industrial Engine Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft
D8T TRACK-TYPE TRACTORS Machine Systems Pump Control Valve (Pressure and Flow Compensator)
3512E Tier 4 Final Engines for Land Electric Drilling Engine Shutdown Occurs Intermittently