Parking Brake - Disassemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-0074 | Slide Hammer Puller Gp | 1 |
8B-7557 | Threaded Adapter | 1 |
Start by:
a. Remove the Parking Brake.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected always.
- Remove bolts (1) that are used to disengage the parking brake.
Show/hide table
Illustration 2 g06020171 - Install bolts (1) in the three holes, as shown. Remove bolts (2) and the washers evenly.
- Remove retaining plate (3) from brake housing (4).
Show/hide table
Illustration 3 g06020172 - Remove spacers (5) from the brake housing.
Show/hide table
Illustration 4 g06020174 - Use Tooling (A) to remove pistons (6) from the brake housing.
Show/hide table
Illustration 5 g06020175 - Loosen bolts (7) evenly until the spring tension against brake housing (4) is released. Remove bolts (7).
Note: Note the location of bolts (7) for installation purposes.
Show/hide tableIllustration 6 g06020178 - Use two people to remove brake housing (4) from bearing cage assembly (8). The weight of brake housing (4) is approximately
50 kg (110 lb) .Show/hide tableIllustration 7 g06020179 - Remove lip seals (9), backup rings (10), and brake seals (11) from brake housing (4).
Show/hide table
Illustration 8 g06020182 - Remove springs (12) and pressure plate (13).
Show/hide table
Illustration 9 g06020184 - Remove clutch plates (14) and brake discs (15).
Show/hide table
Illustration 10 g06020186 - Remove bolt (16) and retainer (17) from the brake shaft.
Show/hide table
Illustration 11 g06020188 - Remove seal (18) and hub (20) from brake shaft (19).
Show/hide table
Illustration 12 g06020189 - Use a suitable rubber mallet to tap brake shaft (19) out of the bottom side of bearing cage assembly (8).
Show/hide table
Illustration 13 g06020192 - Remove lip seal (21), ring (22), and bearing (23) from bearing cage assembly (8).
- If necessary, remove dowels (24).
Show/hide table
Illustration 1 | g06020169 |
Caterpillar Information System:
990K Wheel Loader and 844K Wheel Dozer Machine Systems Automatic Lubrication - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Accumulator Charging Valve (Brake) - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Piston Pump (Hydraulic Fan) - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Piston Pump (Implement) - Remove and Install
Check the Dump Body on AD55B, and AD60 Underground Articulated Trucks {7258} Check the Dump Body on AD55B, and AD60 Underground Articulated Trucks {7258}
Improved Transmission Oil Cooler Fan Now Used on AD60 Underground Articulated Trucks {1375} Improved Transmission Oil Cooler Fan Now Used on AD60 Underground Articulated Trucks {1375}
C175-16 Locomotive Engine Fuel Flow Is High
C175-16 Locomotive Engine Sensor Signal (Analog, Active) - Test
C175-16 Locomotive Engine Sensor Signal (Analog, Passive) - Test
C175-16 Locomotive Engine Sensor Supply - Test
C175-16 Locomotive Engine Sensor Signal (PWM) - Test
C175-16 Locomotive Engine Coolant Temperature Is High
990K Wheel Loader and 844K Wheel Dozer Machine Systems Boom - Remove and Install
844K Wheel Dozer and 990K Wheel Loader Power Train Torque Converter (Lockup) - Assemble
844K Wheel Dozer and 990K Wheel Loader Power Train Parking Brake - Assemble
990K Wheel Loader and 844K Wheel Dozer Machine Systems Boom Bearings and Seals - Remove and Install
C4.4 Engines DEF Pressure Does Not Respond
990K Wheel Loader and 844K Wheel Dozer Machine Systems Piston Pump (Brake) - Remove and Install
950L and 962L Wheel Loaders Solenoid Valve (Switch Controlled) - Test
973K Track-Type Loader Machine Systems Cab - Remove and Install
Procedure To Install PLE641 Cellular Radio Product Link In Place Of PLE631 Satellite Radio Product Link, Or PLE631 Satellite Radio Product Link In Place Of PLE641 Cellular Radio Product Link On Certain M-Series Medium Wheel Loaders {7490, 7606, 7610, Procedure To Install PLE641 Cellular Radio Product Link In Place Of PLE631 Satellite Radio Product Link, Or PLE631 Satellite Radio Product Link In Place Of PLE641 Cellular Radio Product Link On Certain M-Series Medium Wheel Loaders {7490, 7606, 7610,
950L and 962L Wheel Loaders Speed Sensor - Test
An Improved Air Lines Group Is Now Used On Certain D5R and D6N Track Type Tractors {1071} An Improved Air Lines Group Is Now Used On Certain D5R and D6N Track Type Tractors {1071}
Improved Tilt Cylinder Head End Relief Valves Are Used on Certain 986H Wheel Loaders {5051, 5051, 5104} Improved Tilt Cylinder Head End Relief Valves Are Used on Certain 986H Wheel Loaders {5051, 5051, 5104}