An Improved Clip on the 421-7246 Hose As is now used on Certain D11T Track-Type Tractors {5068}
- Track-Type Tractor
- D11T (S/N: AMA1-UP; MDG1-UP; JEL1-UP; JNS1-UP)
Description Of Change: An improved clip for the hydraulic hose is now used in the high-pressure screens attachment group.
This hose runs from the implement pump discharge to the inner rear screen port. The improved clip has a grommet to prevent the hose from rubbing. The power train pump drive shaft guard was also changed to allow clearance for the larger clip.
Adaptable To: This improvement is effective with the following machines:
- D11T (S/N: JEL412-UP; AMA618-UP; MDG180-UP; JNS135-UP)
- D11T (S/N: JEL1-411; AMA1-617; MDG1-179; JNS1-134)
Show/hide table
| Required Parts | |||
| Item | Qty | Part Number | Description |
| 1 | 1 | 5P-7468 | Clip |
| 2 | 1 | 5P-7469 | Clip |
| 3 | 1 | 5P-8444 | Grommet |
| 4 | 1 | 7X-0311 | Bolt |
| 5 | 1 | 8T-5360 | Washer |
| 6 | 1 | 213-6754 | Boss |
- Remove existing clip (A) from 421-7246 Hose As (B).
Show/hide table
Illustration 2 g06013727 - Install clip (1), clip, (2), grommet (3), bolt (4), washer (5), and boss (6).
Note: Check the clearance between the clip and the power train pump drives shaft guard. If needed, grind off corner (C) of the guard as shown in Illustration 2 to obtain sufficient clearance.
Show/hide table
| |
| Illustration 1 | g06013738 |
Caterpillar Information System:
631K Wheel Tractor-Scraper Operator Controls
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loader Machine Systems Piston Pump (Hydrostatic) - Assemble
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loader Machine Systems Lift Arms - Remove and Install
D6 Track-Type Tractor Welding on Machines with Electronic Controls
Improved Powered Access System is Now Available for Certain Large Wheel Loaders and Large Wheel Dozers {7254, 7255, 7256} Improved Powered Access System is Now Available for Certain Large Wheel Loaders and Large Wheel Dozers {7254, 7255, 7256}
D7E Track-Type Tractor Power Train Systems ECM Swap - Test
D7E Track-Type Tractor Power Train Systems Wiring Harness (Short Circuit) - Test
D7E Track-Type Tractor Power Train Systems Wiring Harness (Open Circuit) - Test
D7E Track-Type Tractor Power Train Systems Switch Circuits - Test
D7E Track-Type Tractor Power Train Systems Starting System - Test
D7E Track-Type Tractor Power Train Systems Connector Contact Description
D7E Track-Type Tractor Power Train Systems ECM - Replace
910K, 914K and 920K Compact Wheel Loaders Cooling System Coolant (ELC) - Change
An Additional Ride Control Accumulator is Now Available on Certain 988K Wheel Loaders {5004, 5054, 5057, 5066, 5077} An Additional Ride Control Accumulator is Now Available on Certain 988K Wheel Loaders {5004, 5054, 5057, 5066, 5077}
Secondary Speed Timing Sensor Harness Inspection on Certain C18 Engines {1408} Secondary Speed Timing Sensor Harness Inspection on Certain C18 Engines {1408}
910K, 914K and 920K Compact Wheel Loaders Fire Extinguisher Location
Caterpillar Machine Fluids Recommendations Reference Material
An Improved O-Ring Seal Is Now Used On Certain D8 Track-Type Tractor Angle Blade Tilt Cylinders {5104} An Improved O-Ring Seal Is Now Used On Certain D8 Track-Type Tractor Angle Blade Tilt Cylinders {5104}
910M, 914M, and 918M Compact Wheel Loaders Rated Load
910M, 914M, and 918M Compact Wheel Loaders Battery Disconnect Switch
844K Wheel Dozer and 990K Wheel Loader Power Train Output Transfer Gears - Disassemble
953K Track-Type Loader Machine Systems Pump Mounting - Remove and Install
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loader Machine Systems Control Manifold - Remove and Install - (Differential Lock) (Hydraulic Lockout)
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install