Lift Arms - Remove and Install
Start By:
- Release the hydraulic system pressure.
- Remove the quick coupler.
- Remove the tilt lever.
- Remove the lift cylinder.
Show/hide table
 |
|
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
- Remove clamps (1) and (3). Relocate the hoses from lift arms. Remove hose assemblies (2) from the lift arms.
Show/hide table
Illustration 3 g06008392 - Relocate harness assembly (4).
Show/hide table
Illustration 4 g06008411 - Support lift arms (5) with a suitable lifting device.
Show/hide table
Illustration 5 g06008428 - Remove bolts (6) and the retainer. Remove pin (7). Repeat for the other side.
- Remove lift arm (5). The weight of lift arm (5) is approximately
390 kg (860 lb) .
Show/hide table
| |
| Illustration 1 | g06008262 |
Show/hide table
| |
| Illustration 2 | g06008280 |
- Install lift arms (5) in the reverse order of removal.
Caterpillar Information System:
D6 Track-Type Tractor Welding on Machines with Electronic Controls
Improved Powered Access System is Now Available for Certain Large Wheel Loaders and Large Wheel Dozers {7254, 7255, 7256} Improved Powered Access System is Now Available for Certain Large Wheel Loaders and Large Wheel Dozers {7254, 7255, 7256}
D7E Track-Type Tractor Power Train Systems ECM Swap - Test
D7E Track-Type Tractor Power Train Systems Wiring Harness (Short Circuit) - Test
D7E Track-Type Tractor Power Train Systems Wiring Harness (Open Circuit) - Test
D7E Track-Type Tractor Power Train Systems Switch Circuits - Test
D7E Track-Type Tractor Power Train Systems Starting System - Test
D7E Track-Type Tractor Power Train Systems Connector Contact Description
D7E Track-Type Tractor Power Train Systems ECM - Replace
D7E Track-Type Tractor Power Train Systems ECM - Configure
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loader Machine Systems Piston Pump (Hydrostatic) - Assemble
631K Wheel Tractor-Scraper Operator Controls
An Improved Clip on the 421-7246 Hose As is now used on Certain D11T Track-Type Tractors {5068} An Improved Clip on the 421-7246 Hose As is now used on Certain D11T Track-Type Tractors {5068}
910K, 914K and 920K Compact Wheel Loaders Cooling System Coolant (ELC) - Change
An Additional Ride Control Accumulator is Now Available on Certain 988K Wheel Loaders {5004, 5054, 5057, 5066, 5077} An Additional Ride Control Accumulator is Now Available on Certain 988K Wheel Loaders {5004, 5054, 5057, 5066, 5077}
Secondary Speed Timing Sensor Harness Inspection on Certain C18 Engines {1408} Secondary Speed Timing Sensor Harness Inspection on Certain C18 Engines {1408}
910K, 914K and 920K Compact Wheel Loaders Fire Extinguisher Location
Caterpillar Machine Fluids Recommendations Reference Material
An Improved O-Ring Seal Is Now Used On Certain D8 Track-Type Tractor Angle Blade Tilt Cylinders {5104} An Improved O-Ring Seal Is Now Used On Certain D8 Track-Type Tractor Angle Blade Tilt Cylinders {5104}
910M, 914M, and 918M Compact Wheel Loaders Rated Load
910M, 914M, and 918M Compact Wheel Loaders Battery Disconnect Switch
844K Wheel Dozer and 990K Wheel Loader Power Train Output Transfer Gears - Disassemble