Combustion Body Group (ARD) - Remove
Removal Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
 |
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
 |
Show/hide table
|
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately. |
|
- Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
- Disconnect tube assembly (1). Remove gasket (2) .
Show/hide table
 | |
| Illustration 1 | g01376054 |
Show/hide table
 | |
| Illustration 2 | g01376064 |
- Loosen clamp (6) and position tube assembly (1) out of the way.
- Disconnect flame detection temperature sensor (3) .
- Disconnect cable assembly (4) and disconnect cable assembly (5) .
- Remove hoses (7), hose (8), hose (9), hose (10) and hose (11) .
Show/hide table
 | |
| Illustration 3 | g01376088 |
- Disconnect flame detection temperature sensor (14) .
Show/hide table
 | |
| Illustration 4 | g01375293 |
- Remove nuts (15) .
- Loosen clamp assembly (12) and remove tube assembly (13) .
- Disconnect turbocharger outlet temperature sensor (17) .
Show/hide table
 | |
| Illustration 5 | g01375266 |
- Loosen clamp assembly (18) and remove combustion body group (16) .
Caterpillar Information System:
G3520B Industrial Engines Component Location
2007/07/30 An Update to the Maintenance Interval Schedule for Some Caterpillar Marine Engines {1063}
G3520B Industrial Engines System Overview
C15 On-Highway Engine Solenoid Valve (ARD) - Remove and Install
C7 Marine Engine Piston and Rings
C3.4 Engines for Caterpillar Built Machines Balancer - Assemble
C3.4 Engines for Caterpillar Built Machines Balancer - Disassemble
C15 On-Highway Engine Fuel Control Manifold (ARD) - Install
C15 On-Highway Engine Fuel Control Manifold (ARD) - Assemble
Installation of the 129-2288 Shaft {1205, 1353, 1356, 1359} Installation of the 129-2288 Shaft {1205, 1353, 1356, 1359}
G3520B Industrial Engines Crankshaft
G3520B Industrial Engines Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
G3520B Industrial Engines Configuration Parameters
Cat Commercial Diesel Engine Fluids Recommendations Characteristics of Diesel Fuel
Cat Commercial Diesel Engine Fluids Recommendations Fuel Recommendations
C32 Marine Propulsion Engines Coolant Level - Test
C15 On-Highway Engine Combustion Body Group (ARD) - Install
Procedure to Update the Head Gasket on the Air Compressor on Caterpillar On-Highway Engines{1803, 7555} Procedure to Update the Head Gasket on the Air Compressor on Caterpillar On-Highway Engines{1803, 7555}
3516C Locomotive Engine Electrical System
3516C Locomotive Engine Model View Illustrations
C15 On-Highway Engine Combustion Head Group (ARD) - Remove and Install
C15 and C18 Industrial Engines Engine Cranks but Does Not Start
3176C, 3406E and 3456 Industrial Engines Engine Does Not Crank
2007/07/09 A Gasket for the Cooling System has been Improved {1380, 7555}