Transmission - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7505 | Hydraulic Jack | 1 |
B | 439-3940 | Link Bracket | 3 |
386-6031 | Lever Puller Hoist Gp | 1 |
Start By:
- Remove the front hydrostatic piston motor and the rear hydrostatic piston motor.
- Remove bolts (1) and the caps in order to disconnect drive shaft (2) from the yoke. Discard bolts (1).
Show/hide table
Illustration 2 g02802476 - Remove cover (3).
Show/hide table
Illustration 3 g02802517 - Disconnect harness assemblies (4) and (5). Reposition harness assemblies (4) and (5) out of the way.
Show/hide table
Illustration 4 g02802564 - Disconnect harness assembly (6) and reposition harness assembly (6) out of the way.
Show/hide table
Illustration 5 g02802576 - Remove bracket (7).
Show/hide table
Illustration 6 g02802636 - Disconnect harness assembly (8). Disconnect tube assembly (9). Reposition filter base (10) out of the way.
Show/hide table
Illustration 7 g02802997 - Disconnect harness assembly (11).
Show/hide table
Illustration 8 g02803036 - Disconnect hose assembly (12).
Show/hide table
Illustration 9 g02803097 - Remove clamp (13) and bolts (15). Reposition tube assembly (14) and hose assembly (16) out of the way.
Show/hide table
Illustration 10 g02803276 - Position Tooling (A) under transmission (17). The weight of transmission (17) is approximately
145 kg (320 lb) . Use suitable straps in order to secure transmission (17) to Tooling (A).Show/hide tableIllustration 11 g02803363 - Remove bolts (18).
Show/hide table
Illustration 12 g02803536 - Remove bolts (19).
Show/hide table
Illustration 13 g02803541 - Remove bolts (20).
Show/hide table
Illustration 14 g02803577 - Use Tooling (A) in order to lower transmission (17).
Show/hide table
Illustration 15 g02803580 Show/hide tableIllustration 16 g02803606 Show/hide tableIllustration 17 g02803617 - Position a suitable bar across transmission mounts (21). Attach Tooling (B) to the suitable bar and transmission (17). The weight of transmission (17) is approximately
145 kg (320 lb) . - Disconnect the straps that secure transmission (17) to Tooling (A). Use Tooling (B) in order to raise transmission (17) off Tooling (A). Remove Tooling (A).
- Use Tooling (A) in order to lower transmission (17) to the ground.
Show/hide table
Illustration 1 | g02802456 |
- Install transmission (17) in the reverse order of removal.
- Install new bolts (1) and tighten until snug. Tighten bolts (1) to a torque of
71 ± 10 N·m (52 ± 7 lb ft) using an X pattern.
- Install new bolts (1) and tighten until snug. Tighten bolts (1) to a torque of
Caterpillar Information System:
D6K2 and D6K Track-Type Tractor Systems Accumulator (Pilot) - Test and Charge
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Hydraulic System Oil Level - Check
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Assemble - Front Hydrostatic Piston Motor
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Assemble - Rear Hydrostatic Piston Motor
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Disassemble - Rear Hydrostatic Piston Motor
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Engine Air Filter Service Indicator - Inspect/Replace
2014/10/29 New Condenser Fan Is Now Used on Certain D7E Track-Type Tractors {1805, 5701, 7610, 7620}
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Disassemble - Front Hydrostatic Piston Motor
D6R2 Track-Type Tractor Engine Supplement Alternator - Remove and Install
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Engine Air Filter Primary Element - Clean/Replace
930K Wheel Loader Power Train Piston Motor (Hydrostatic) - Remove and Install - Front Hydrostatic Piston Motor
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Cooling System Coolant Level - Check
926M, 930M and 938M Wheel Loaders Power Train Transmission - Assemble
926M, 930M and 938M Wheel Loaders Power Train Transmission - Disassemble
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Radiator Core - Clean
Installing the 443-0881 Precleaner Gp On Certain D7E Track-Type Tractors{1055} Installing the 443-0881 Precleaner Gp On Certain D7E Track-Type Tractors{1055}
C27 and C32 Engines for Caterpillar Built Machines Cooling Fan Control - Test
D6K2 and D6K Track-Type Tractor Systems Operational Checks
2014/12/09 Improved Power Train Compartment Oil Level Gauge Assembly Is Now Used on Certain D8R Track-Type Tractors {3016}
D3K2, D4K2 and D5K2 Track-Type Tractor Systems Electronic Control (Winch System)
926M, 930M and 938M Wheel Loaders Power Train Gear Pump (Hydrostatic, Charge) - Remove and Install
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Window Washer Reservoir - Fill
926M, 930M and 938M Wheel Loaders Power Train Gear Pump (Hydrostatic, Charge) - Disassemble
926M, 930M and 938M Wheel Loaders Power Train Gear Pump (Hydrostatic, Charge) - Assemble