Fuel Injection Control Linkage - Install
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install shaft assembly (13) through the opening in the rear of the engine.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Show/hide table
 | |
| Illustration 1 | g01307157 |
- Install bracket (10) with the bolts.
- Install shaft assembly (12) through the opening in the rear of the engine.
- Install the nut, the washers, and bolts (11) that connect shaft assemblies (12) and (13) together.
- Install flange (14) onto the rear of the cylinder block.
- Install rod assembly (9) onto the fuel control shaft.
Show/hide table
 | |
| Illustration 2 | g01307150 |
- Install lever (8) onto plate assembly (7) .
Show/hide table
 | |
| Illustration 3 | g01208609 |
- Place plate assembly (7) into position in rocker arm support (6). Install the bolts for plate assembly (7) .
- Install lever (3) into rod assembly (5) .
Show/hide table
 | |
| Illustration 4 | g01208606 |
Show/hide table
 | |
| Illustration 5 | g00629802 |
- Install rod assembly (5) and lever (3) as a unit.
- Install bolt (4) .
- Place lever (3) into position on the control shaft. Install cap (2) and bolt (1) .
- Install the camshaft inspection covers for each side of the engine.
- Adjust the fuel injection control linkage. Refer to Testing and Adjusting, "Fuel Setting".
End By:
- Install the camshaft drive gears. Refer to Disassembly and Assembly, "Camshaft Drive Gear - Install".
- Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Caterpillar Information System:
3176C, 3406E and 3456 Industrial Engines Oil Contains Coolant
C15 and C18 Petrolem Generator Set Engines Oil Consumption Is Excessive
Exhaust Temperature Module Mounting
Exhaust Temperature Module Thermocouples
C11 and C13 Engines and 14M and 16M Motor Graders Intake Manifold Air Temperature Is High
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Fuel System Primary Filter/Water Separator - Drain
C11 and C13 Engines and 14M and 16M Motor Graders Inlet Air Is Restricted
Exhaust Temperature Module System Description
C11 and C13 Engines and 14M and 16M Motor Graders Idle Speed Is High
2006/09/25 Correct Installation Procedure for the 235-1448 Tube As {1306}
C13 On-highway Engine Diesel Particulate Filter
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Temperature Is High
CX35 On-Highway Transmission Reference Material
Exhaust Temperature Module Wiring
TH48-E70 Petroleum Transmission and TH48-E70-C27I, TH48-E70-C32I and TH48-E70-C32P Petroleum Power Train Packages Transmission Hydraulic Control
C15 and C18 Petrolem Generator Set Engines Power Is Intermittently Low or Power Cutout Is Intermittent
3176C, 3406E and 3456 Industrial Engines General Information
3126E On-highway Engine Connecting Rod Bearings - Remove
C175-16 Locomotive Engine ECM - Configure
C13 and C15 On-Highway Engines Stopping the Engine
2006/09/01 Improved Variable Valve Actuator (VVA) Pressure Sensors Are Available {5078}
Exhaust Temperature Module Alarm Description
2006/10/02 Improvements for the Tandem Couplings {3252, 4450}
C32 Power Module Refill Capacities and Recommendations