 | |
| Illustration 1 | g01695973 |
(1) Lockup clutch
- Thickness of three new discs and of two new plates ... 21.35 ± 0.34 mm (0.841 ± 0.013 inch)
Thickness of one new 8E-8328 Friction Disc ... 4.83 ± 0.08 mm (0.190 ± 0.003 inch)
Thickness of one new 1T-1897 Plate ... 3.43 ± 0.05 mm (0.135 ± 0.002 inch)
 | |
| Illustration 2 | g00293522 |
Bolt Tightening Sequence for Bolts (2) | |
(2) Torque for 12 bolts ... 50 ± 7 N·m (37 ± 5 lb ft)
Use the following procedure to tighten 12 bolts (2) :
Tighten four of the bolts in numbered sequence 1 through 4. Then, tighten all 12 bolts in numbered sequence 5 through 16. Overlap the starting point in order to make sure that all of the bolts are at the required torque.
(3) Torque for eight bolts ... 50 ± 7 N·m (37 ± 5 lb ft)
(4) Torque for eight bolts ... 50 ± 7 N·m (37 ± 5 lb ft)
(5) Put a small amount of lubricant on the lip of the seal before installation.
(6) Torque for twelve bolts ... 120 ± 15 N·m (89 ± 11 lb ft)
(7) Torque for three bolts ... 120 ± 15 N·m (89 ± 11 lb ft)
(8) 1T-1257 Springs for one-way clutch
- Quantity ... 2
- Length under test force ... 17.8 mm (0.70 inch)
- Test force ... 30.74 ± 1.96 N (6.91 ± 0.44 lb)
- Free length after test ... 27.4 mm (1.08 inch)
- Outside diameter ... 5.84 mm (0.230 inch)
- Length under test force ... 17.8 mm (0.70 inch)
(9) Torque for twelve bolts ... 80 ± 10 N·m (59 ± 7 lb ft)
 | |
| Illustration 3 | g00293523 |
Bolt Tightening Sequence for Bolts (10) | |
(10) Torque for 24 bolts ... 240 ± 25 N·m (177 ± 18 lb ft)
Use the following procedure to tighten 24 bolts (10) :
Tighten eight of the bolts in numbered sequence 1 through 8. Then, tighten all 24 bolts in numbered sequence 9 through 32. Overlap the starting point in order to make sure that all of the bolts are at the required torque.
 | |
| Illustration 4 | g00293524 |
Bolt Tightening Sequence for Bolts (12) | |
(11) Torque for 24 bolts ... 80 ± 10 N·m (59 ± 7 lb ft)
Use the following procedure to tighten 24 bolts (12) :
Tighten eight of the bolts in numbered sequence 1 through 8. Then, tighten all 24 bolts in numbered sequence 9 through 32. Overlap the starting point in order to make sure that all of the bolts are at the required torque.
(12) Torque for six bolts ... 30 ± 5 N·m (22 ± 3 lb ft)
(13) Torque for 14 bolts ... 50 ± 7 N·m (37 ± 5 lb ft)
| Components | Clearance Across The Diameter | Running (1) | |
| (A) Stator and Turbine | new | 0.71 to 0.91 mm (0.028 to 0.036 inch) |
0.36 to 0.46 mm (0.014 to 0.018 inch) |
| max worn |
1.83 mm (0.072 inch) |
0.91 mm (0.036 inch) |
|
| (B) Stator and Impeller | new | 0.71 to 0.91 mm (0.028 to 0.036 inch) |
0.36 to 0.46 mm (0.014 to 0.018 inch) |
| max worn |
1.83 mm (0.072 inch) |
0.91 mm (0.036 inch) |
|
| ( 1 ) | One half of the clearance across the diameter |