Piston Pump (Steering) - Remove and Install
Removal Procedure
Start By:
- Remove the cab.
Show/hide table
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
- Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
- Remove tube assemblies (1) and (2) .
Show/hide table
Illustration 1 | g02666456 |
- Remove clip (3) .
- Disconnect hose assembly (4) .
- Disconnect hose assemblies (5) and (6) .
Show/hide table
Illustration 2 | g02666657 |
- Disconnect tube assembly (7) .
Show/hide table
Illustration 3 | g02666719 |
- Disconnect clip (8) and position tube assembly (7) out of the way.
Show/hide table
Illustration 4 | g02666722 |
- Remove bracket assembly (9) .
- Remove bracket (11). Attach a suitable lifting device to steering piston pump (10). The weight of steering piston pump (10) is approximately 50 kg (110 lb).
Show/hide table
Illustration 5 | g02666728 |
- Remove bolts (12) and remove steering piston pump (10) .
Show/hide table
Illustration 6 | g02666720 |
Show/hide table
Illustration 7 | g02666958 |
- Remove coupling (13) and O-ring seal (8) .
Show/hide table
Illustration 8 | g02668997 |
Installation procedure
- Install steering piston pump (10) on the reverse order of removal.
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Flywheel - Inspect
C4.4 Engines for Caterpillar Built Machines Electric Starting System - Test
950K Wheel Loader and 962K Wheel Loader Power Train Differential (Standard)
D3K2, D4K2 and D5K2 Track-Type Tractors Machine Systems Pump Drive Coupling
2013/08/21 Calculating Cylinder Liner Projection for 3500, 3500B, 3500C, and G3500 Engines {1201, 1216}
D11T Track-Type Tractor Power Train Transmission Hydraulic Control
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Pilot Oil Accumulator (Dead Engine, Lift Arm Lower) - Test and Charge
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
950K Wheel Loader and 962K Wheel Loader Power Train Engine and Transmission Mounting
950K Wheel Loader and 962K Wheel Loader Power Train Output Transfer Gears
950K and 962K Wheel Loaders Machine Systems Steering Control Valve (Command Control Steering) - Assemble
854K Wheel Dozer Electrohydraulic System Main Control Valve
C4.4 Engines for Caterpillar Built Machines Connecting Rod - Inspect
924K, 930K and 938K Wheel Loaders Electrohydraulic System Gear Motor (Hydraulic Fan)
C4.4 Engines for Caterpillar Built Machines Crankshaft Pulley - Check
C4.4 Engines for Caterpillar Built Machines Gear Group - Inspect
854K Wheel Dozer and 992K Wheel Loader Power Train Connector Locations
D6N Track-Type Tractor MID 039 - CID 1884 - FMI 03
D6N Track-Type Tractor MID 039 - CID 1884 - FMI 05
Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239} Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239}
621H, 623H and 627H Wheel Tractor-Scrapers Engine Supplement Transmission Oil Cooler - Remove and Install - Tractor
992K Wheel Loader Electrohydraulic System Breaker Relief Valve - European Union
854K Wheel Dozer Electrohydraulic System Machine Preparation for Troubleshooting