Radiator Core - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
开始:
- 拆下后冷器。 请参阅拆解和组装, "后冷器 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下上部和下部散热器护罩 (1) 。
Show/hide table
图 1 | g01292911 |
- 将工具 (A) 和适当的起吊设备固定到散热器顶部水箱 (2) 上。 散热器的重量约为 227 kg (500 lb)。
Show/hide table
图 2 | g01292912 |
- 拆下上部和下部支架 (3) 。
Show/hide table
图 3 | g01294577 |
- 拆下螺栓 (4) 和螺栓 (5) 。
Show/hide table
图 4 | g01294578 |
- 拆下螺栓 (6) 。
Show/hide table
图 5 | g01294579 |
- 拆下螺栓 (7) 。 拆下螺栓 (8) 。 拆下支承 (9) 。
Show/hide table
图 6 | g01294580 |
- 对于另一侧,重复步骤4 至6。
- 拆下螺栓 (11) 。 对另一侧重复此操作。 拆下散热器 (10) 。
Show/hide table
图 7 | g01294602 |
Caterpillar Information System:
C27 and C32 Generator Set Engines Fuel Filter and Water Separator - Remove and Install
C27 and C32 Generator Set Engines Fuel Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Pressure Sensor - Remove and Install
C15 and C18 Petrolem Generator Set Engines Symptom Troubleshooting
C27 and C32 Generator Set Engines Fuel Filter Base - Install
C27 and C32 Generator Set Engines Fuel Filter Base - Remove
2006/08/01 Improved Support for the Precooler is Now Used {105P, 1380}
C27 and C32 Generator Set Engines Fuel Priming Pump - Remove and Install
C13 Engine Engine Oil Filter Base and Oil Cooler - Remove
C13 Engine Engine Oil Filter Base and Oil Cooler - Install
2006/10/16 Test Cable Group Checks Three-Wire, Active Analog Circuits That Are Used in Sensors {0779, 0785}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Personal Computer to UPS Connection
C15 and C18 Petrolem Generator Set Engines Alternator Problem - Charging Problem and/or Noisy Operation
C15 and C18 Petrolem Generator Set Engines Coolant Contains Fuel
3408E and 3412E Engines for Caterpillar Built Machines Engine Has Mechanical Noise (Knock)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Vacuum Pump Startup - Required Procedure After Extended Storage
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Low DC Voltage Potentiometer - Calibrate
3176C, 3406E and 3456 Industrial Engines Oil Contains Fuel
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Multidrop Network - Setup
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Remote Input/Output Dry Contact - Setup
C175-16 Locomotive Engine Cylinder Block, Liners and Heads
Troubleshooting Engine Vibration{1000, 1151, 1162, 1206} Troubleshooting Engine Vibration{1000, 1151, 1162, 1206}
3508B, 3512B, and 3516B High Displacement Generator Sets Maintenance Recommendations
Failure To Program Injector 6 Trim Calibration File{1290, 7620} Failure To Program Injector 6 Trim Calibration File{1290, 7620}