980K Wheel Loader Machine Systems Caterpillar

Assembly Procedure

Show/hide table

Illustration 1	g00670525

1. Use the proper equipment to handle bearing cone (54). Raise the temperature of bearing cone (54). Install bearing cone (54) onto shaft assembly (49).
   Show/hide table

   Illustration 2	g00670361

2. Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup (53) and install the bearing cup in pump body (27).
   Show/hide table

   Illustration 3	g00670360

3. Inspect the O-ring seals on plugs (52). Replace the O-ring seals, if necessary. Install plugs (52) in pump body (27).
   Show/hide table

   Illustration 4	g00670531

   Show/hide table

   Illustration 5	g00670532

4. Install retaining ring (50). Use Tooling (A) to install seal (51) (not shown).
   Show/hide table

   Illustration 6	g00670298

5. Install shaft assembly (49).

6. Use the following steps to determine the proper preload on the bearings of the pump assembly.
   Show/hide table

   Illustration 7	g00669728

   1. Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup (30) and install the bearing cup in head assembly (26).
      Show/hide table

      Illustration 8	g00670604
      Typical Example

   2. Install adjustment shim (33) and bearing cone (32) onto shaft assembly (49).
      Show/hide table

      Illustration 9	g00670605

   3. Position head assembly (26) onto pump body (27).
      Show/hide table

      Illustration 10	g02580696

   4. Use Tooling (C) in order to measure the distance between the head and the pump housing.

   5. Take measurements at three equal intervals on the surface between the head and the pump housing.

   6. The average of the three dimensions should be between zero and 0.05 mm (0.002 inch).

   7. If necessary, grind adjustment shim (33) in order to obtain the correct dimension between the head and the pump housing. It may be necessary to replace the shim with a new part.
      Show/hide table

      Illustration 11	g02580532

   8. Install bolts (25) in the head and pump body (27). Tighten bolts (25) to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
      Show/hide table

      Illustration 12	g00670626

   9. Use Tooling (D), Tooling (E), and Tooling (F) to check end play in shaft assembly (49). If end play exists in the shaft assembly, repeat Step 6 until the correct dimension between the head and the pump housing is reached.

   10. Remove bolts (25) and head assembly (26) from pump body (27). Remove bearing cone (32) and adjustment shim (33) from shaft assembly (49).

   11. Proceed with the assembly of the fan drive pump.
   Show/hide table

   Illustration 13	g00670223

7. Install bearings (48).
   Show/hide table

   Illustration 14	g00670207

8. Install spring (47).
   Show/hide table

   Illustration 15	g00670206

9. Install swashplate (46).
   Show/hide table

   Illustration 16	g00670205

   Show/hide table

   Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

   Note: Note that there is a correct connection of the piston rod and the swashplate.

10. Install piston rod (45).
    Show/hide table

    Illustration 17	g00670204

11. Install control piston (44).
    Show/hide table

    Illustration 18	g00669745

    Show/hide table

    Illustration 19	g00669744

    Show/hide table

    Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment.

    Note: There is spring force against retaining ring (43). When retaining ring (43) is not seated properly, the spring force will be released. Installation of the internal components in barrel (38) should be performed in a press. This is done in order to retain spring (42) and retaining ring (43).

12. Install pins (40), guide (41) and spring (42) in barrel assembly (38).

13. Use a suitable press and Tooling (A) to compress the spring (42) in barrel assembly (38).

14. Use Tooling (B) to install retaining ring (43).

15. Slowly release compression on spring (42). Make sure that the retaining ring (43) is seated properly.
    Show/hide table

    Illustration 20	g00669743

16. Install retaining ball (39) on barrel assembly (38).
    Show/hide table

    Illustration 21	g00669741

17. Install piston assemblies (37) in barrel assembly (38).
    Show/hide table

    Illustration 22	g00669742

18. Install rotary group (36) onto the shaft. Make sure that the splines are aligned properly.
    Show/hide table

    Illustration 23	g00669738

19. Install O-ring seal (34) on plug (35).
    Show/hide table

    Illustration 24	g00669732

20. Install plug (34).
    Show/hide table

    Illustration 25	g00669731

21. Install adjustment shim (33).
    Show/hide table

    Illustration 26	g00669730

22. Install bearing cone (32) onto shaft assembly.
    Show/hide table

    Illustration 27	g00669729

23. Install O-ring seal (31).
    Show/hide table

    Illustration 28	g00669727

24. Install O-ring seal (28) and port plate (29) on head assembly (26).
    Show/hide table

    Illustration 29	g02580532

25. Install head assembly (26) and four bolts (25). The torque for the bolts (25) is 100 ± 20 N·m (75 ± 15 lb ft).
    Show/hide table

    Illustration 30	g00670203

26. Install spool (23) in compensator valve (1). Install spacer (24) onto plug (22).

27. Install plug (22) in compensator valve (1).
    Show/hide table

    Illustration 31	g02581078

    Show/hide table

    Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

28. Install O-ring seal (17) to plug (16). Install plate (18), spring (19), spring (20), and guide (21) in compensator valve (1).

29. Install plug (16) in compensator valve (1).
    Show/hide table

    Illustration 32	g00670198

30. Install spool (14) in compensator valve (1). Install spacer (15) on plug (13).

31. Install plug (13) in compensator valve (1).
    Show/hide table

    Illustration 33	g02581076

    Show/hide table

    Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

32. Install O-ring seal (8) to plug (7). Install plate (9), spring (10), spring (11), and guide (12) in compensator valve (1).

33. Install plug (7) in compensator valve (1).
    Show/hide table

    Illustration 34	g00670191

34. Install O-ring seal (6) on plug (5).
    Show/hide table

    Illustration 35	g00670190

35. Install plugs (5) in compensator valve (1).
    Show/hide table

    Illustration 36	g00670188

36. Inspect O-ring seals (4) and replace the O-ring seals, if necessary. Install O-ring seals (4) on compensator valve (1).
    Show/hide table

    Illustration 37	g00669721

37. Install bolts (2) and pressure and flow compensator valve (1) to piston pump (3).

End By:

1. Install the fan drive pump.