Air Starting Motor - Disassemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-1854 | 挡圈钳 | 1 |
B | - | 盘
50.8 mm (2 inch) × 102 mm (4 inch) × 6 mm (0.25 inch) |
2 |
C | 1P-1857 | 挡圈钳 | 1 |
D | - | 六角扳手(5/16 英寸) | 1 |
开始:
- 拆卸气动马达。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 拆解空气起动马达之前,请确保有一整套新垫片、叶片、密封件和 O 形密封圈。
注: 下图显示了从发动机上卸下的空气起动马达部件的不同方向。 使用给定的步骤。 将空气起动马达上的组件保持对齐。
- 标记壳体以便显示马达壳体 (1) 相对于齿轮箱 (4) 的位置,以便装配。 卸下螺栓 (2) 以便从马达壳体 (1) 上将齿轮箱 (4) 和传动壳体 (3) 作为一个整体卸下。
Show/hide table
图 2 g01284203 - 使用工具 (A) 从主动齿轮 (5) 上卸下挡圈 (6)。
Show/hide table
图 3 g01284204 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
注: 从起动马达的小齿轮端检查马达时,标准发动机旋转的空气起动马达沿顺时针方向转动。 顺时针转动的起动马达的螺栓 (7) 上有左手螺纹。
注: 从起动马达的小齿轮端检查马达时,反向发动机旋转的空气起动马达沿逆时针方向转动。 逆时针转动的起动马达的螺栓 (7) 上有右手螺纹。
- 卸下螺栓 (7) 和垫圈 (8),以便从传动轴端部卸下主动小齿轮 (9)、套筒和弹簧。
- 标记传动壳体 (3) 相对于齿轮箱 (4) 的位置,以便装配。 从齿轮箱 (4) 上卸下螺栓 (10) 和传动壳体 (3)。
Show/hide table
图 4 g01284214 - 从传动壳体 (3) 上卸下 O 形密封圈 (11)。
Show/hide table
图 5 g01284221 Show/hide table活塞固定压缩的弹簧。 为防止人身伤害,小心地卸下将活塞固定到位的环。 缓慢释放弹簧的张力。
Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 将工具 (B) 安装在主动齿轮 (5) 和活塞 (12) 之间。 适当施压以便压缩活塞回位弹簧。 卸下将传动轴组件和活塞固定在壳体 (3) 上的挡圈。
Show/hide table
图 6 g01284838 - 缓慢释放压力,以便消除活塞回位弹簧 (14) 所受压力。 从主动齿轮和活塞 (12) 上卸下工具 (B)。 从活塞上卸下挡圈 (13)。 将主动齿轮、活塞和传动轴组件作为一个整体从传动壳体 (3) 上卸下。 从传动壳体上卸下活塞回位弹簧 (14)。
Show/hide table
图 7 g01284231 - 使用工具 (D) 拧松主动齿轮螺栓,直至螺纹完全拧开。 将传动轴组件 (15) 和活塞 (12) 作为一个整体从主动齿轮 (5) 上卸下。
Show/hide table
图 8 g01284233 - 从活塞 (12) 上卸下闷头 (16)。
- 从闷头 (16) 上卸下 O 形密封圈 (17)。
Show/hide table
图 9 g01284251 - 从活塞 ( 12) 上卸下挡圈 (18)。 从传动轴组件 (15) 上卸下活塞。
Show/hide table
图 10 g01284252 注: 新款空气起动马达没有减振垫 (20)。
- 从活塞 (12) 上卸下 O 形密封圈 (21)、减振垫 (20) 和密封件 (19)。
Show/hide table
图 11 g01284258 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 从传动轴组件 (15) 上卸下挡圈 (30)、杯形件 (29)、弹簧 (28)、从动离合器叉 (27)、驱动离合器叉 (26)、轴承 (25)、垫片 (24)、锁紧垫圈 (23) 和螺栓 (22)。
Show/hide table
图 12 g01284263 注: 卸下挡圈 (31) 时,挡圈必须替换为新挡圈。
- 卸下挡圈 (31) 以便从传动轴组件 (15) 上卸下轴承 (32)。
Show/hide table
图 13 g01284370 - 使用工具 (C) 卸下挡圈 (34)。 从齿轮箱 (4) 上卸下轴承 (33)。
Show/hide table
图 14 g01284371 Show/hide table图 15 g01284374 注: 新款空气起动马达将没有减振垫 (35) 和备用环 ( 36)。
- 从传动壳体 (3) 上卸下减振垫 (35) 和备用环 (36)。
Show/hide table
图 16 g01284384 - 从传动壳体 (3) 上卸下座 (37) 和轴承 (38)。
Show/hide table
图 17 g01284388 - 从传动壳体 (3) 上卸下密封件 (39)。
Show/hide table
图 18 g01284390 - 标记盖组件 (40) 相对于马达壳体 (1) 的位置,以便装配。 从马达壳体上卸下盖组件和 O 形密封圈。
Show/hide table
图 19 g01284858 - 卸下螺栓 (42),以便从转子轴上卸下转子小齿轮 (41)。
Show/hide table
图 20 g03477160 - 松开螺栓 (44)。 从转子轴上卸下螺母 (43)。
Show/hide table
图 21 g03477459 - 使用合适的撬具拆下端板 (47)。
- 拆下轴承 (45) 和弹簧垫圈 (46)。
Show/hide table
图 22 g03478157 - 使用合适的压具从轴承 (49) 和端板 (50) 上拆下转子 (48)。
Show/hide table
图 23 g03478657 - 拆下 O 型密封圈 (51)。
Show/hide table
图 24 g03479389 - 将轴承 (49) 从端板 (50) 上拆下。
Show/hide table
图 25 g03479500 - 将 O 形密封圈 (52) 从油缸 (53) 上拆下。
Show/hide table
图 26 g03479657 - 从马达壳体 (1) 上卸下油缸 (53)。 从油缸上卸下其余的 O 形密封圈。
Show/hide table
图 1 | g01284201 |
Caterpillar Information System:
C175-16 and C175-20 Generator Set Engines Fuel Lines
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys 24V Power Supply
3612 and 3616 Engines Air Starting Motor - Remove
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Power Distribution PWA
3612 and 3616 Engines Air Starting Motor Silencer - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys DC Disconnect Indicator
3612 and 3616 Engines Air Lubricator - Remove and Install
2006/06/26 Calibration of the ECPC Valves on Well Servicing OEM Transmissions {3073, 3139, 3167, 4800, 4808, 7000}
C175-16 and C175-20 Generator Set Engines Fan Drive
2006/11/27 The 285-0910 Multi-Tool Gp Incorporates Four Diagnostic Tools into a Single, Hand Held Unit {0774, 0779, 0781, 0782}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys DC Disconnect Switch Handle
C280-12 and C280–16 Marine Engines Mounting Isolator - Remove and Install
G3508, G3512 and G3516 Engines Electric Starting Motor - Remove and Install
Inspection and Repair Procedure to Replace the Studs for the Rocker Arm Shaft{1102} Inspection and Repair Procedure to Replace the Studs for the Rocker Arm Shaft{1102}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Dual Network Interface PWA (Flywheel Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys General Purpose Interface PWA (Flywheel Cabinet)
G3500 A3 Engines Gas Engine Ignition
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Bearing Preload - Check
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys CT Interface PWA
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Vacuum Pump Oil - Change
3500B Industrial Engine Speed Sensor - Clean/Inspect
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Precharge Contactor (K1, K2)
3500 Generator Sets Overhaul Considerations
3512C Engine for Caterpillar Built Machines Diagnostic Code List