1. Home
  2. Caterpillar
  3. Testing and Adjusting
  4. #i02903056

993K Wheel Loader Electrohydraulic System Caterpillar


Position Sensor (Lift Linkage) - Replace

Usage:

993K Z9K

  • Tilt the bucket to a position level with the ground. Lower the bucket to the ground.

  • Connect the steering frame lock link.

  • Engage the parking brake.

  • Stop the engine and leave the key start switch in the OFF position.
    Show/hide table
    Illustration 1g01618377
    Right Side of Front Frame
    (1) Lift Linkage Position Sensor

  • Disconnect the harness connector from the sensor connector.

  • Remove the bracket from the frame.

  • Remove the lever from the Lift Linkage Position Sensor.

  • Remove the Lift Linkage Position Sensor from the bracket.

    Show/hide table
    NOTICE

    The position sensor can be damaged if too much force is applied against the internal stops of the sensor. Be careful when removing the position sensor lever or rotating the shaft attached to the sensor.

  • Install the new Lift Linkage Position Sensor on the bracket.

  • Install the lever on the new Lift Linkage Position Sensor.

  • Install the bracket on the frame.

  • Connect the harness connector to the sensor connector.

  • The Lift Linkage Position Sensor must be calibrated before the machine is returned to use.

    Reference: For the correct procedure to calibrate the Lift Linkage Position Sensor, refer to the Service Manual module Testing And Adjusting, KENR5828, "993K Wheel Loader Hydraulic System", "Calibrations (Operator Monitor)" for the machine that is being serviced.

    • Caterpillar Information System:

    993K Wheel Loader Electrohydraulic System MID 082 - CID 0353 - FMI 04
    C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Misfires, Runs Rough or Is Unstable
    2008/01/07 Rework Procedure For The Fender and Fender Bracket {7252}
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0595 - FMI 05
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0595 - FMI 06
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0594 - FMI 03
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0593 - FMI 03
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0593 - FMI 13
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0594 - FMI 05
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0593 - FMI 06
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0355 - FMI 05
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0352 - FMI 04
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0800 - FMI 09
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0595 - FMI 13
    993K Wheel Loader Electrohydraulic System Service Tools
    993K Wheel Loader Electrohydraulic System MID 082 - CID 0595 - FMI 03
    993K Wheel Loader Power Train Using the Operator Monitor to Determine Diagnostic Codes
    992K Wheel Loader Machine Systems Main Control Valve - Disassemble
    938H Wheel Loader and IT38H Integrated Toolcarrier Machine Systems Toggle Switch (Hood Tilt)
    854K Wheel Dozer Hydraulic System Features - VIMS
    2007/12/24 The Orientation of the Right Hand Steering Hoses have been Improved {4304}
    2008/02/11 Transmission and Engine Software Update for Certain Medium Wheel Loaders {1901, 1902, 7610, 7620}
    844H Wheel Dozer Additional Messages
    824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor System Pressure Release
    Back to top
    Contacts My AVS
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.