Engine Oil Cooler - Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the mating surfaces of the oil cooler base (9) and the oil cooler body (4). If the oil cooler base (9) was removed, clean the mating surfaces of the oil cooler base and the cylinder block.
Show/hide table
Illustration 2 g01041030 Tightening sequence Note: Do not use sealant on the new joint between the cylinder block and the oil cooler base (9).
- If the oil cooler base (9) was removed from the cylinder block, install setscrews into setscrew holes (1) and (6) in the oil cooler base. Install a new joint onto the two setscrews and secure the oil cooler base (9) to the cylinder block. Install the remainder of the setscrews (8). Tighten the setscrews (8) in the sequence 1, 2, 3, 4, 5, and 6 to a torque of
22 N·m (16 lb ft) . Refer to the illustration 2.Show/hide tableIllustration 3 g01041194 - Install new O-rings (5) and (6) onto the oil cooler body (4). Position the oil cooler body (4) onto the oil cooler base (9).
- Install a new sealing ring (7) onto the adapter (3). Install the adapter (3) through the oil cooler body (4) and into the oil cooler base (9). Tighten the adapter (3) to a torque of
57 N·m (42 lb ft) . - Install the appropriate hose to the coolant outlet (2). Tighten the hose clamp to a torque of
3.5 N·m (31 lb in) . - Install the appropriate hose to the coolant inlet (1). Tighten the hose clamp to a torque of
3.5 N·m (31 lb in) . - Fill the cooling system with coolant. Fill the lubrication system with engine oil. Refer to the Operation and Maintenance Manual, "Refill Capacities" for the cooling system capacity and for the lubrication system capacity of the engine.
Show/hide table
Illustration 1 | g01041195 |
Caterpillar Information System:
C3.3 Industrial Engine Engine Oil Cooler - Remove
C6.6 Generator Set Indicator Lamp Circuit - Test
C6.6 Generator Set Injector Solenoid Circuit - Test
C3.3 Industrial Engine Finding Top Center Position for No. 1 Piston
3126B and 3126E Truck Engines Fan Drive
C6.6 Engines for Caterpillar Built Machines Engine Oil Filter Base
3126B and 3126E Truck Engines Belt Tensioner
2006/02/13 Five New Wrenches Remove Snap To Connect Couplings from Hydraulic Hose Assemblies {0602, 0738, 5057}
C11 and C15 Engines for Caterpillar Built Machines E362 Engine Overspeed
Incorrect SENS Battery Chargers Installed on Griffin-Packaged 3306, 3406, 3412, 3456, G3406 and G3412 Engine Generator Sets{1401} Incorrect SENS Battery Chargers Installed on Griffin-Packaged 3306, 3406, 3412, 3456, G3406 and G3412 Engine Generator Sets{1401}
3126B and 3126E Truck Engines Belt Tensioner
C11 and C13 Petroleum Engines Monitoring System - If Equipped
C280 Marine and Petroleum Engines Engine Speed/Timing Wheel
C3.3 Industrial Engine Engine Oil Pump - Remove
C3.3 Industrial Engine Engine Oil Pump - Install
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Joystick Controls Alternate Patterns - If Equipped
2006/01/02 Troubleshooting Engines with New Scroll Fuel Systems (NSFS) {1000, 1254}
2006/02/01 Troubleshooting Engines with New Scroll Fuel Systems (NSFS) {1250}
C6.6 Engines for Caterpillar Built Machines Engine Oil Pump
C6.6 Engines for Caterpillar Built Machines Water Pump
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Leakage - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System
2006/01/02 Troubleshooting Engines with Mechanical Unit Injection (MUI) {1000, 1254}
C6.6 Engines for Caterpillar Built Machines Connecting Rod