Brake and Planetary
Show/hide table
Illustration 1 | g01302140 |
(1) 9M-4335 Reaction dowel
- Quantity ... 7
- Length ... 76.2 mm (3.0 inch)
- Diameter ... 12.636 ± 0.013 mm (.4975 ± .0005 inch)
- Length ... 76.2 mm (3.0 inch)
(2) 8R-0923 Spring
- Quantity ... 3
- Length under test force ... 27.3 mm (1.07 inch)
- Test force ... 335 N (75 lb)
- Free length after test ... 37.2 mm (1.46 inch)
- Outside diameter ... 21.8 mm (.86 inch)
- Length under test force ... 27.3 mm (1.07 inch)
(3) Planetary Shaft and Sleeve Bearing
- Diameter of 8R-3252 Planetary Shaft ... 47.981 ± 0.008 mm (1.8890 ± .0003 inch)
- Inside diameter of 9C-6029 Planetary Bearing ... 48.039 ± 0.039 mm (1.891 ± 0.0015 inch)
(4) Planetary Gear and Sleeve Bearing
- Outside diameter of 9C-6029 Planetary Bearing ... 57.439 ± 0.013 mm (2.2614 ± .0005 inch)
- Inside diameter of 9U-2787 Planetary Gear or 9C-6032 Planetary Gear ... 57.536 ± 0.010 mm (2.2652 ± .0004 inch)
(5) Thickness of a new 100-3597 Reaction plate ... 10 mm (.39 inch)
(6) 6I-8030 Friction disc
- The thickness of a new friction disc ... 9.10 ± .13 mm (.358 ± .005 inch)
- The minimum depth of the oil grooves that are on a new friction disc ... 1.05 mm (.041 inch)
- The recommended minimum thickness of a worn friction disc ... 8.05 mm (.317 inch)
- The recommended minimum depth of the oil grooves that are on a worn friction disc ... 0.53 mm (.021 inch)
- The minimum depth of the oil grooves that are on a new friction disc ... 1.05 mm (.041 inch)
Note: The oil grooves are essential for the cooling of the brake discs. Replacement of the friction discs is recommended after fifty percent of the original depth is worn off of the oil groove on either side of the disc.
(7) Thickness of a new 8R-0942 Reaction plate ... 23.4 mm (.92 inch)
(8) (9) Install the seals dry, and then coat the entire assembly with petroleum jelly.
(9) Install the backup ring on the seal, as shown.
Caterpillar Information System:
C13 Engines for Caterpillar Built Machines Engine Misfires, Runs Rough or Is Unstable
C175-16 Locomotive Engine Pressure Sensor
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Sensors
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Switches
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Electronic Control Module (ECM)
D7G and D7G Series II Track-Type Tractors Power Train Transmission Lubrication Relief Valve - Install
D6G Series II Track-Type Tractor Machine Systems Bank Valve (Implement) - Install
D6G Series II Track-Type Tractor Machine Systems Bank Valve (Implement) - Remove
D6G Series II Track-Type Tractor Power Train Brake Hydraulic Control and Actuating Mechanism - Install
AccuGrade® Laser (CD610) Configuration (Single Mast System)
D6G Series II Track-Type Tractor Power Train Brake Hydraulic Control and Actuating Mechanism - Remove
AD55B Underground Articulated Truck Dumping
2006/10/02 Updated Track Guide Guards {4177}
G3520C and G3520E Generator Set Engines Welding Precaution
G3600 Engines Programmable Parameters
G3600 Engines Symptom Troubleshooting
AD55B Underground Articulated Truck Stopping the Machine
AD55B Underground Articulated Truck Stopping the Engine
AD55B Underground Articulated Truck Lifting and Tying Down the Machine
G3520C and G3520E Generator Set Engines Turbocharger Turbine Temperature Is Low
AD55B Underground Articulated Truck Tire Shipping Pressure
AD55B Underground Articulated Truck Capacities (Refill)
AD55B Underground Articulated Truck Filter and Screen Locations
AD55B Underground Articulated Truck Sampling Interval and Location of Sampling Valve