Parking Brake - Remove
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (1) and reposition center drive shaft (2) to the side.
Show/hide table
Illustration 1 | g03615137 |
- Position yoke (3) , as shown, in order to allow the brake drum to be removed.
Show/hide table
Illustration 2 | g03615141 |
- Release the parking brake.
- Remove pins (7) and (8) in order to disconnect rod (6) from lever (9) .
Show/hide table
Illustration 3 | g03615146 |
- Activate the parking brake in order to will allow rod (6) to be retracted out of the way.
- Drain the transmission oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Transmission Oil - Change".
- Remove bolts (5) and reposition brake actuator (4) .
- Remove bolts (11) and brake hub (10) .
Note: The steering cylinder on the left side must be removed in order to remove brake drum (11) from the machine. Refer to Disassembly and Assembly, "Steering Cylinder - Remove and Install".
- Remove bolt (12) , retainer (13) , and O-ring seal (14) .
Show/hide table
Illustration 4 | g03615153 |
- Remove yoke (3) .
- Remove bolts (15) and brake assembly (16) .
Show/hide table
Illustration 5 | g03615156 |
Caterpillar Information System:
D7R Series II Track-Type Tractor Power Train Oil Filter and Base (Power Train) - Assemble
D7R Series II Track-Type Tractor Power Train Oil Filter and Base (Power Train) - Disassemble
AccuGrade® GPS (CD700) Glossary
AccuGrade® GPS (CD700) Troubleshooting Techniques
AccuGrade® GPS (CD700) End User License Agreement
AccuGrade® GPS (CD700) Machine Symbols
AccuGrade® GPS (CD700) Full Screen Messages
AccuGrade® GPS (CD700) Flashing Messages
AccuGrade® GPS (CD700) Common Problems
AccuGrade® GPS (CD700) General Maintenance Information
AccuGrade® GPS (CD700) Design Surface Type
AccuGrade® GPS (CD700) General Information
525C, 535C and 545C Wheel Skidders Power Train Parking Brake - Install
D7R Series II Track-Type Tractor Power Train Oil Filter and Base (Power Train) - Install
525C, 535C and 545C Wheel Skidders Power Train Parking Brake Actuator - Remove
525C, 535C and 545C Wheel Skidders Power Train Parking Brake Actuator - Install
525C, 535C and 545C Wheel Skidders Power Train Torque Converter from Transmission - Separate
525C, 535C and 545C Wheel Skidders Power Train Torque Converter to Transmission - Connect
854K Wheel Dozer Hydraulic System Oil Level (Implement) (Hydraulic Fan) - Check
854K Wheel Dozer Hydraulic System Oil Level (Steering) (Brake) - Check
525C, 535C and 545C Wheel Skidders Power Train Bottom Guard (Engine) - Remove and Install
525C, 535C and 545C Wheel Skidders Power Train Bottom Guard (Transmission) - Remove and Install
854K Wheel Dozer Hydraulic Tank Breaker Relief Valve - Clean
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Clutch (Reverse, Second)