Inlet Manifold - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 8C-8422 | 密封胶 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 涂敷在进气歧管 (2) 的接合面上。 必须在 10 分钟内安装好进气歧管 (2) 。 将进气歧管 (2) 安置在缸体上。 安装进气加热器电磁阀的支架组件和螺栓 (1) 。
Show/hide table
 | |
| 图 1 | g01156405 |
- 如有必要，安装进气加热器。
- 将工具 (A) 涂敷在进气弯头 (3) 的接合面上。 必须在 10 分钟内安装好进气弯头 (3) 。 将进气弯头 (3) 安置在进气歧管 (2) 上并安装螺栓 (6) 。
- 将线束组件 (5) 连接到进气歧管 (2) 上。
- 将线束组件 (4) 连接到进气弯头 (3) 上。
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Inlet Manifold - Remove
C9 Engines for Caterpillar Built Machines Cylinder Head - Remove
C15 and C18 Engines for Caterpillar Built Machines E198 Low Fuel Pressure
C9 Engines for Caterpillar Built Machines Water Pump - Assemble
C15 Generator Set Engines CID 0102 FMI 04 Boost Pressure Sensor short to ground
C15 Generator Set Engines CID 0102 FMI 03 Boost Pressure Sensor short to +batt
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0358 - FMI 06
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0358 - FMI 05
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0358 - FMI 03
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0355 - FMI 06
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0355 - FMI 05
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0355 - FMI 03
515, 525, 525B, 525C, 535B, 535C, 545 and 545C Wheel Skidders Winch System Pressure - Release
904B Wheel Loader Engine Supplement Electric Starting Motor - Remove and Install
621G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect/Replace - If Equipped
657G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect/Replace
904B Wheel Loader Engine Supplement Battery and Battery Cable - Separate and Connect
C9 Engines for Caterpillar Built Machines Cylinder Head - Install
C9 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
657G Wheel Tractor-Scraper Cooling System Coolant Sample (Level 1) - Obtain
631G Wheel Tractor-Scraper Engine Oil (High Speed) and Oil Filter - Change
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0489 - FMI 03
C9 Engines for Caterpillar Built Machines Fan Drive - Remove
904B Wheel Loader Engine Supplement Water Temperature Regulator - Remove and Install