Track Roller - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 4C-6486 | Stand | 1 |
| 8S-7621 | Tube | 1 | |
| 8S-8048 | Saddle | 1 | |
| 8S-7615 | Pin | 1 | |
| B(1) | 9U-7489 | Lift Stand | 2 |
| B1 | OR | ||
| 504-9791 | Lift Gp (60 Hz)(2) | 2 | |
| 504-9793 | Lift Gp (50 Hz)(3) | 2 | |
| C | FT-2213 | Strap | 1 |
| D | 183-4799 | Track Roller Lifting Fork | 1 |
Show/hide table
| (1) | Use Tooling (B) or (B1) based on requirements. |
| (2) | Operating Voltage (240-480V) |
| (3) | Operating Voltage (200-400V) |
- Detension the track. Refer to Operation and Maintenance Manual, "Track - Check/Adjust".
Show/hide table
Illustration 1 g01142126 - Lower the blade onto Tooling (A).
Show/hide table
Illustration 2 g01142129 Show/hide table
Illustration 3 g01142135 For Tooling (B). - Position Tooling (B) under the front and rear of the machine. Use Tooling (B) to raise the side of the machine.
Show/hide table
Illustration 4 g06387879 Show/hide table
Illustration 5 g06387882 For Tooling (B1). - Position Tooling (B1) under the front and rear of the machine. Use Tooling (B1) to raise the side of the machine. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (B1).
Show/hide table
Illustration 6 g01140471 - Install Tooling (C).
Show/hide table
Illustration 7 g01142140 - Remove bolts (1) from track guide (2).
Show/hide table
Illustration 8 g01142146 - Install Tooling (D) to track roller (5). Attach a suitable lifting device to Tooling (D). The weight of track roller (5) is approximately
95 kg (209 lb) . - Remove bolts (4) and caps (3).
Show/hide table
Illustration 9 g01142154 - Use Tooling (D) to remove track roller (5).
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Engine Shutdown Switch Circuit - Test
994F Wheel Loader Hydraulic System Implement Cycle Time - Check
994F Wheel Loader Hydraulic System Lift and Tilt Cylinder Drift - Check
994F Wheel Loader Hydraulic System System Pressure - Release
994F Wheel Loader Braking System Monitoring System (Brake Functions)
994F Wheel Loader Braking System General Information
994F Wheel Loader Braking System Brake Control Valve (Parking)
D6T Track-Type Tractor Cooling System Water Temperature Regulator - Replace
C11 and C15 Engines for Caterpillar Built Machines Electrical Power Supply Circuit - Test
3126B Engines Engine Oil Pressure - Test
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 1964 - FMI 00
D6T Track-Type Tractor Cooling System Coolant Sample (Level 2) - Obtain
C27 Engines for Track-Type Tractors Event Codes
2005/02/21 Information Release Memo, PELJ0481 , "Product Line Expansion for Caterpillar Low and Medium Pressure Hose and Coupling Products" {5057}
988H and 988K Wheel Loaders Power Train Transmission Planetary - Assemble
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201} Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
D8T, D9T, D10T and D11T Track-Type Tractors Machine Movement - D10T
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 1964 - FMI 01
834H Wheel Dozer and 836H Landfill Compactor Power Train Transmission, Input Transfer Gears and Output Transfer Gears - Remove
C11 and C15 Engines for Caterpillar Built Machines 5 Volt Engine Pressure Sensor Supply Circuit - Test
2005/03/21 New Engine Software Provides the Engine Idle Management System {1901, 1902, 7620}
2005/01/31 Hardened Inserts Are Now Available for the Bucket Pin Bores {6107, 6109}
2005/02/07 An Improved Hydraulic Oil Cooler Is Now Available for Machines that Are Equipped with Axle Oil Coolers {1365, 1374}
2005/02/07 A New High Capacity Battery Is Now Available {1401}