Track - Connect - Non-PPR2
连接步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 260-9412     | 链条组件     | 1     |
B     | 5P-6214     | 履带挡块组件     | 2     |
C     | 5P-2379     | 履带压力工具总成     | 1     |
8S-7172 | 双作用油缸     | 1     | |
8S-9903 | 履带压力滚翻总成     | 1     | |
D     | 5P-0960     | 润滑脂筒     | 1     |
E     | 254-8168     | 润滑脂销套件     | 1     |
F     | 129-8708     | 润滑脂     | 1     |
G     | 5P-1725     | 安装工具     | 1     |
- 利用适当的起吊设备升起履带组件前端。 将工具 (B) 安装就位到履带板下方。 升高履带,直到履带链中的销孔对齐为止。
Show/hide table
图 1 | g01206205 |
- 将密封件 (3) 和止推环 (4) 安装到连杆沉孔中。 将工具 (D) 涂抹到止推环 (4) 上,以将止推环 (4) 固定在沉孔中。 将工具 (D) 涂抹到密封件 (3) 的密封唇上。
Show/hide table
图 2 | g01205525 |
- 定位主连杆销 (5) ,使十字孔 (X) 与位置 (Z) 和位置 (Y) 平衡。 将工具 (D) 涂抹到履带中的主连杆销 (5) 和主连杆孔上。
Show/hide table
图 3 | g01205794 |
- 利用工具 (C) 安装主连杆销 (5) 。 主连杆销 (5) 必须位于履带链的中心位置。
Show/hide table
图 4 | g01205522 |
- 拆下止动块组件 (6) 。
Show/hide table
图 5 | g01205707 |
- 将工具 (E) 安装到主连杆销 (5) 中。 安装工具 (F) ,使其穿过工具 (E) 。
注: 当腔体充满时,工具 (F) 将流出排放孔。
Show/hide table
图 6 | g01205695 |
- 利用工具 (G) 安装止动块组件 (6) 。
注: 将止动块安装到 8 ± 2 mm (0.32 ± 0.08 in) 的深度。
Show/hide table
图 7 | g01205707 |
- 利用工具 (A) 定位履带板 (2) 。 安装螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 500 ± 70 N·m (369 ± 52 lb ft)。 将螺栓 (1) 额外上紧 120 度。
Show/hide table
图 8 | g01167154 |
- 从履带组件两侧拆下工具 (B) 。
Show/hide table
图 9 | g01174955 |
Show/hide table
油脂和机油从安全阀中溢出可能导致人身伤亡。 处于高压下的油脂和机油从安全阀中溢出,可能渗透阀体。 不要通过安全阀来观察油脂是否溢出。 应通过履带或履带调节油缸查看履带是否松脱。 确保通风孔清洁,然后释放履带上的张紧力。 |
- 调整履带张力。 请参阅操作和保养手册, "履带的调整 - 调整"。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner
C175 Generator Set Engines Turbocharger - Remove
C27 and C32 Engines General Information
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track - Separate - Non-PPR2
C9 Marine Engines System Overview
C4.4 and C6.6 Engines Event Codes
2005/09/26 New Turbocharger Water Lines are now Used {1380}
C9 Generator Set Engines System Configuration Parameters
2005/10/03 A New Retaining Plate and Bolts for the Bushing on the Engine Idler Gear are Now Available {1151, 1210, 1234}
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Auxiliary Water Pump - Disassemble
2005/09/26 A New Fuel Lift Pump is Now Available {1256, 1258}
3500 Marine Engines Pistons, Rings and Connecting Rods
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner
C7 and C9 On-highway Engines Reference Material
C175 Generator Set Engines Turbocharger - Install
2005/09/01 Responsibilities for Emission Certified Engines {1000, 1900}
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Pilot Valve (Joystick) - Disassemble
C175 Generator Set Engines Auxiliary Water Pump - Remove
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Pilot Valve (Joystick) - Assemble
C175 Generator Set Engines Auxiliary Water Pump - Install
C27 and C32 Engines Electronic Control System Components
C27 and C32 Generator Set Engines Electrical Power Supply Circuit - Test
C175 Generator Set Engines Air Cleaner - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Pilot Valve (Travel) - Disassemble