938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Caterpillar


Additional Messages

Usage:

938G II B9Y
There are several specific messages on this machine. The exact location of the messages and the description of the messages are reviewed in this section. Please become familiarized with all messages.


Illustration 1g01069739

Make sure that all of the messages are legible. Clean the messages or replace the messages if you cannot read the words.

When you clean the messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.

Replace the illustrations if the illustrations are not legible. Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part.

Consult your Caterpillar dealer for replacement of messages.

Lifting or Tying Down the Machine (1)

This message is located on the left side of the machine.




Illustration 2g01070801

Reference: For more information, refer to Operation and Maintenance Manual, "Lifting and Tying Down the Machine".

Air Conditioner (2)

This message is located on the left cab door.




Illustration 3g00983944

Radial Seal Air Filters (3)

This message is located on the cover for the engine air filter.




Illustration 4g01070791


NOTICE

This machine uses radial seal type air cleaners. To avoid engine damage, use only radial seal replacement filters. Others will not seal.

Radial seal filter gasket design and location are critical to proper air cleaner operation. Use only Caterpillar replacements.


No Step (4)

This message is centered on the top of the hood.




Illustration 5g00906093

Do not use the hood as a step. Deformation of the hood can occur.

Caterpillar Information System:

3524B Engine for Caterpillar Built Machines Bearing Clearance - Check
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Transmission Oil Cooler - Remove and Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Lift Kickout - Adjust
924H, 924HZ, 928HZ and 930H Wheel Loaders Fuel Tank Cap and Strainer - Clean
D6N Track-Type Tractor Hydraulic System Troubleshooting
AD30 Underground Articulated Truck Fire Extinguisher Location
AD30 Underground Articulated Truck Safety Messages
AD30 Underground Articulated Truck Steering System General Information
D6N Track-Type Tractor Hydraulic System Pilot Valve (Steering) - Test and Adjust
D6N Track-Type Tractor Hydraulic System Case Pressure (Steering Pump) - Check
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Transmission Output Gears
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Air Compressor - Remove and Install
D6R Series II Track-Type Tractor Pivot Shaft Oil Level - Check
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader System Schematic
Troubleshooting Compressed Air System Components and Performance{1803, 5500} Troubleshooting Compressed Air System Components and Performance{1803, 5500}
D6N Track-Type Tractor Power Train Location of Power Train Components
G3500B Engines Lubrication System
966H and 972H Wheel Loaders Quick Coupler - Check - If Equipped
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader General Information
G3500B Engines Cylinder Block, Liners and Heads
G3500B Engines Pistons, Rings and Connecting Rods
3408E and 3412E Engines for Caterpillar Built Machines Excessive Engine Oil Consumption - Inspect
2003/04/21 A New Yoke Is Now Used in the Lift Cylinder Mounts {5102, 5103, 6068, 7562}
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Aftercooler - Remove and Install - Aftercooler Housing with 12 bolts
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.