Cylinder Head - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 138-7575 | 连杆支架 | 1 |
开始:
- 拆下摇臂和摇臂轴。 请参阅拆解和组装, "摇臂和摇臂轴 - 拆卸"。
- 拆下气门机构罩盖底座。 请参阅拆解和组装, "气门机构罩盖底座 - 拆卸和安装"。
- 拆下风扇驱动装置。 请参阅拆解和组装, "风扇驱动装置 - 拆卸"。
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 将冷却液从冷却系统中排入合适的容器，以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却液（ELC）- 更换"。
- 拆下螺栓 (1) ，然后拆下支架组件 (2) 。 断开电缆组件 (3) 。 断开管组件 (4) 。
Show/hide table
 | |
| 图 1 | g01156402 |
- 断开线束组件 (5) 、 (6) 和 (7) 。
Show/hide table
 | |
| 图 2 | g01156406 |
- 从涡轮增压器上断开管组件 (8) 。
- 断开软管组件 (9) 。
- 拆下螺栓 (10) 。
- 将工具 (A) 和适当的起吊设备固定到缸盖 (11) 。 缸盖 (11) 的重量约为 181 kg (400 lb)。 拆下缸盖 (11) 和密封垫。
Show/hide table
 | |
| 图 3 | g01156425 |
注: 注意不要损坏喷油器端部。
Caterpillar Information System:
C280 Marine and Petroleum Engines Turbocharger
C15 and C18 Engines for Caterpillar Built Machines E198 Low Fuel Pressure
C9 Engines for Caterpillar Built Machines Water Pump - Assemble
C9 Marine Auxiliary and Marine Generator Set Engines Event Codes
C9 Marine Auxiliary and Marine Generator Set Engines CID 0269 FMI 03 Sensor Supply too high
C9 Marine Auxiliary and Marine Generator Set Engines CID 0164 FMI 01 Injector Actuation Pressure below normal
C15 Generator Set Engines CID 0102 FMI 04 Boost Pressure Sensor short to ground
C15 Generator Set Engines CID 0102 FMI 03 Boost Pressure Sensor short to +batt
C9 Marine Auxiliary and Marine Generator Set Engines CID 0042 FMI 07 Injector Actuation Valve improper response
3500 Generator Sets Product Description
C9 Generator Set Engines Fuel System Pressure - Test
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Filter Base
C-12 Generator Set Engine E362 Engine Overspeed
C27 and C32 Industrial and Petroleum Engines Air Inlet and Exhaust Lines
C18 Marine Generator Set Starting the Engine
C18 Marine Generator Set Cold Weather Starting
C9 Engines for Caterpillar Built Machines Cylinder Head - Install
C18 Marine Generator Set Manual Stop Procedure
G3400 Engines (EIS) Diagnostic Code Will Not Clear
C27 and C32 Industrial and Petroleum Engines Belt Tightener
C9 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
G3400 Engines (EIS) Electronic Service Tool Will Not Communicate with ECM
3618 Engine Product Storage
C18 Marine Generator Set Generator Operation