Track Roller - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 8S-7611     | 管组件     | 2     |
8S-7615 | 销     | 2     | |
8S-7640 | 台架     | 2     | |
B     | 183-4797     | 履带支重轮起重叉车     | 1     |
注: 机器两侧各有一个履带导向器。 遵循以下步骤以拆下带有履带导向器的履带支重轮。
- 起动发动机。 把机器停放在坚硬的水平地面上。 停止发动机。
- 松开张紧的履带。 转动安全阀 (1) 仅一圈以松开此阀。 如果履带在安全阀打开后没有放松,请前后移动机器,直到释放张紧度。
Show/hide table
油脂和机油从安全阀中溢出可能导致人身伤亡。 处于高压下的油脂和机油从安全阀中溢出,可能渗透阀体。 不要通过安全阀来观察油脂是否溢出。 应通过履带或履带调节油缸查看履带是否松脱。 确保通风孔清洁,然后释放履带上的张紧力。 |
Show/hide table
图 1 | g00489342 |
- 升起机器的一侧。 如图所示,将工具 (A) 安装在底盘系统下方。
Show/hide table
图 2 | g00489826 |
注: 调整工具 (A) 的高度,以便当工具 (A) 安装在机器的底盘系统下时,有足够的间隙用于拆下履带支重轮。
- 松开将履带导向器 (2) 固定至底盘系统的螺栓。
注: 此时请勿拆下螺栓。
Show/hide table
图 3 | g00664654 |
- 将适当的起吊设备固定到工具 (B) 上。 将工具 (B) 放置在履带导向器 (2) 下,如图所示。 拆下固定履带导向器的螺栓。 拆下履带导向器。
Show/hide table
图 4 | g00664663 |
- 如果已配有摇动防护装置,请从底盘系统拆下。
Show/hide table
图 5 | g00664665 |
(X) 摇动防护装置 |
- 松开将履带支重轮 (3) 固定至底盘上的螺栓。
注: 此时请勿拆下螺栓。
Show/hide table
图 6 | g00664675 |
- 将适当的起吊设备和吊带连接到工具 (B) 上。
- 将工具 (B) 放置在履带支重轮 (3) 下,如图所示。
- 拆下固定履带支重轮的螺栓。 拆下履带支重轮。 履带支重轮的重量约为 40 kg (88 lb)。
参考有关履带支重轮的拆解和组装步骤,请参阅底盘系统修复公报, SEBF8568, "液压挖掘机滚轮拆解和组装过程"。
Caterpillar Information System:
637G Wheel Tractor-Scraper Functional Test (Caterpillar Monitoring System)
3412E Engine for Caterpillar Built Machines Injector Solenoid Circuit - Test
D8R Series II Track-Type Tractor After Starting Engine
2002/11/11 Support Literature Is Now Available For Maintaining Excavator Heating and Air Conditioning Systems {7309, 7320}
637G Wheel Tractor-Scraper General Information (Caterpillar Monitoring System)
2000/02/14 The Track Rollers With Symmetric Duo-Cone Seals Have Been Improved {4180, 7561}
621G Wheel Tractor-Scraper Engine Overspeed Test Switch
D8R Series II Track-Type Tractor Walk-Around Inspection
988G Wheel Loader Power Train Bypass Switch (Power Train Oil Filter)
2000/01/10 Field Returns Of The Lift Pressure Sensor and The Tilt Pressure Sensor Are Necessary for Failure Analysis and Product Improvement {7601}
621G Wheel Tractor-Scraper Steering Column Tilt and Telescope Control
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train Calibration and Programming
973C Track-Type Loader Engine Supplement Hydraulic Oil Cooler - Remove
988G Wheel Loader Power Train Relief Valve (Torque Converter Outlet)
824G Wheel Tractor, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Relief Valve (Main) - Test and Adjust
988G Wheel Loader Power Train Modulating Valve (Torque Converter Lockup Clutch)
973C Track-Type Loader Engine Supplement Hydraulic Oil Cooler - Install
988G Wheel Loader Power Train Modulating Valve (Torque Converter Impeller Clutch)
637G Wheel Tractor-Scraper Main Display Module (Caterpillar Monitoring System)
988G Wheel Loader Power Train Axle Oil Cooler
2000/01/03 A New Bracket for the Backup Alarm Switch is Now Available {7406}
924G and 924Gz Wheel Loaders Engine Supplement Engine to Torque Converter and Transmission - Connect
3114, 3116 and 3126 MUI Engine Governors Governor (Type V) - Adjust
973C Track-Type Loader Engine Supplement Radiator Guard - Remove and Install