Unit Injector - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1U-7587 | Pry Bar | 1 |
| B | 147-6456 | Wedge Removal Tool | 1 |
Start By:
- Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: The valve bridges may need to be removed in order to remove the unit injectors. If the valve bridges are removed, the valve lash will need to be set during installation. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
- Use Tooling (B) or a small flat head screwdriver to disconnect harness assembly (2) .
Show/hide table
 | |
| Illustration 1 | g01137288 |
Show/hide table
 | |
| Illustration 2 | g01137290 |
- Remove socket head bolts (3) .
- Place Tooling (A) at location (C) . Carefully remove unit injector (1) from the cylinder head.
- Remove O-ring seals (6) , (7) , and (8) from unit injector (1) . Remove backup rings (4) , (5) , and (9) from unit injector (1) .
Note: Do not use a wire brush on the tip of the injector. Damage to the injector will occur.
Show/hide table
 | |
| Illustration 3 | g01137291 |
Caterpillar Information System:
C9 Urban Transit Bus Engine Fuel Filter Base - Remove and Install
C32 Marine Engine Sensors and Electrical Components
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Pump - Inspect
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Temperature Regulator - Test
C32 Marine Engines Fuel Level Sensor Circuit - Test
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Crankshaft Rear Seal and Wear Sleeve - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Cooling System - Test
3406E, C12, C15 and C18 Marine Engines E113 High Transmission Oil Pressure
C27 and C32 Generator Set Engines E059 Low Engine Coolant Level Warning
C27 and C32 Generator Set Engines E057 Low Engine Coolant Level Derate
3406E, C12, C15 and C18 Marine Engines E053 Low Fuel Pressure Warning
C9 Urban Transit Bus Engine Unit Injector - Install
390F MHPU Mobile Hydraulic Power Unit Condenser (Refrigerant) - Clean
390F MHPU Mobile Hydraulic Power Unit Engine Air Filter Secondary Element - Replace
390F MHPU Mobile Hydraulic Power Unit Radiator Core - Clean
390F MHPU Mobile Hydraulic Power Unit Swing Drive Oil Sample - Obtain
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines ECM Will Not Accept Factory Passwords
C27 and C32 Engines Electrical System
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Charging System - Test
3500B High Displacement Generator Set Engines Refill Capacities and Recommendations
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Glow Plugs - Test
C9 Urban Transit Bus Engine Exhaust Manifold - Remove and Install
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Refill Capacities and Recommendations