Fuel Filter Base - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 185-3630 | Strap Wrench Assembly | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Use Tooling (A) to remove fuel filter (5) .
Show/hide table
 | |
| Illustration 1 | g01137272 |
- Disconnect tube assemblies (1) and (2) from fuel filter base (3). Immediately cap all openings or plug all openings in order to prevent contamination.
- Remove bolts (4). Remove fuel filter base (3) .
Installation Procedure
- Position fuel filter base (3) on the front housing. Install bolts (4) .
Show/hide table
| | |
| Illustration 2 | g01137272 |
- Connect tube assemblies (1) and (2) to the fuel filter base.
- Install fuel filter (5) .
Caterpillar Information System:
C32 Marine Engine Sensors and Electrical Components
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Pump - Inspect
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Temperature Regulator - Test
C32 Marine Engines Fuel Level Sensor Circuit - Test
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Crankshaft Rear Seal and Wear Sleeve - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Cooling System - Test
3406E, C12, C15 and C18 Marine Engines E113 High Transmission Oil Pressure
C27 and C32 Generator Set Engines E059 Low Engine Coolant Level Warning
C27 and C32 Generator Set Engines E057 Low Engine Coolant Level Derate
3406E, C12, C15 and C18 Marine Engines E053 Low Fuel Pressure Warning
3126B Industrial Engines E039 Low Engine Oil Pressure Derate
C9 Urban Transit Bus Engine Unit Injector - Remove
C9 Urban Transit Bus Engine Unit Injector - Install
390F MHPU Mobile Hydraulic Power Unit Condenser (Refrigerant) - Clean
390F MHPU Mobile Hydraulic Power Unit Engine Air Filter Secondary Element - Replace
390F MHPU Mobile Hydraulic Power Unit Radiator Core - Clean
390F MHPU Mobile Hydraulic Power Unit Swing Drive Oil Sample - Obtain
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines ECM Will Not Accept Factory Passwords
C27 and C32 Engines Electrical System
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Charging System - Test
3500B High Displacement Generator Set Engines Refill Capacities and Recommendations
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Glow Plugs - Test
C9 Urban Transit Bus Engine Exhaust Manifold - Remove and Install