Diagnostic Code Cross Reference
Problems with the electronic control system are reported via these types of codes: flash codes, SPN/FMI codes, diagnostic codes, and event codes.
For information on flash codes, refer to Troubleshooting, "Flash Codes".
For information on SPN/FMI codes, refer to Troubleshooting, "Diagnostic Codes".
For information on diagnostic codes, refer to Troubleshooting, "Diagnostic Codes".
For information on event codes, refer to Troubleshooting, "Event Codes".
Cross-Reference for Flash Code to CID-FMI (Diagnostics) or EID (Events)
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Show/hide table
| Cross-Reference for Flash Code to CID-FMI (Diagnostics) or EID (Events) | ||
|---|---|---|
| Flash Code | CID-FMI or EID | Description of Code |
| 13 | 174-03 | Fuel Temperature open/short to +batt |
| 174-04 | Fuel Temperature short to ground | |
| 15 | 96-03 | Fuel Level Sensor open/short to +batt |
| 96-04 | Fuel Level Sensor short to ground | |
| 21 | 262-03 | 5 Volt Sensor DC Power Supply short to +batt |
| 262-04 | 5 Volt Sensor DC Power Supply short to ground | |
| 41-03 | 8 Volt DC Supply short to +batt | |
| 41-04 | 8 Volt DC Supply short to ground | |
| 24 | 100-03 | Engine Oil Pressure open/short to +batt |
| 100-04 | Engine Oil Pressure short to ground | |
| 25 | 102-03 | Boost Pressure Sensor open/short to +batt |
| 102-04 | Boost Pressure Sensor short to ground | |
| 27 | 110-03 | Engine Coolant Temperature open/short to +batt |
| 110-04 | Engine Coolant Temperature short to ground | |
| 28 | 91-13 | Throttle Position Calibration required |
| 1249-13 | Secondary Throttle Position calibration required | |
| 32 | 91-08 | Throttle Position signal abnormal |
| 1249-08 | Secondary Throttle Position signal abnormal | |
| 34 | 190-08 | Engine Speed abnormal |
| 320-02 | Speed/Timing Sensor Loss of Signal | |
| 320-11 | Speed/Timing Sensor mechanical failure | |
| 342-08 | Secondary Engine Speed signal abnormal | |
| 35 | E190 | Engine Overspeed Warning |
| 36 | E268 | Unexpected Engine Shutdown |
| 37 | 94-03 | Fuel Pressure open/short to +batt |
| 94-04 | Fuel Pressure short to ground | |
| 38 | 172-03 | Inlet Manifold Air Temp open/short to +batt |
| 172-04 | Inlet Manifold Air Temp short to ground | |
| 42 | 261-13 | Engine Timing Calibration required |
| 46 | E039 | Low Engine Oil Pressure Derate |
| E100 | Low Engine Oil Pressure Warning | |
| 51 | 168-02 | System Voltage intermittent/erratic |
| 58 | E057 | Low Engine Coolant Level Derate |
| E059 | Low Engine Coolant Level Warning | |
| 59 | 253-02 | Personality Module mismatch |
| 61 | E015 | High Engine Coolant Temperature Derate |
| E017 | High Engine Coolant Temperature Warning | |
| 63 | E053 | Low Fuel Pressure Warning |
| 64 | E025 | High Inlet Air Temperature Derate |
| E027 | High Inlet Air Temperature Warning | |
| 66 | E030 | High Transmission Oil Temperature Warning |
| 67 | 177-03 | Transmission Oil Temperature open/short to +batt |
| 177-04 | Transmission Oil Temperature short to ground | |
| 68 | 127-03 | Transmission Oil Pressure open/short to +batt |
| 127-04 | Transmission Oil Pressure short to ground | |
| 69 | E113 | High Transmission Oil Pressure |
| 71 | 1-05 | Injector Cylinder 1 open circuit |
| 1-06 | Injector Cylinder 1 short | |
| 72 | 2-05 | Injector Cylinder 2 open circuit |
| 2-06 | Injector Cylinder 2 short | |
| 73 | 3-05 | Injector Cylinder 3 open circuit |
| 3-06 | Injector Cylinder 3 short | |
| 74 | 4-05 | Injector Cylinder 4 open circuit |
| 4-06 | Injector Cylinder 4 short | |
| 75 | 5-05 | Injector Cylinder 5 open circuit |
| 5-06 | Injector Cylinder 5 short | |
| 76 | 6-05 | Injector Cylinder 6 open circuit |
| 6-06 | Injector Cylinder 6 short | |
| 77 | 7-05 | Injector Cylinder 7 open circuit |
| 7-06 | Injector Cylinder 7 short | |
| 78 | 8-05 | Injector Cylinder 8 open circuit |
| 8-06 | Injector Cylinder 8 short | |
| 81 | 9-05 | Injector Cylinder 9 open circuit |
| 9-06 | Injector Cylinder 9 short | |
| 82 | 10-05 | Injector Cylinder 10 open circuit |
| 10-06 | Injector Cylinder 10 short | |
| 83 | 11-05 | Injector Cylinder 11 open circuit |
| 11-06 | Injector Cylinder 11 short | |
| 84 | 12-05 | Injector Cylinder 12 open circuit |
| 12-06 | Injector Cylinder 12 short | |
Cross-Reference for SPN-FMI Code to CID-FMI (Diagnostics) or EID (Events)
Show/hide table
| Cross-Reference for SPN(1)-FMI Code to CID-FMI (Diagnostics) or EID (Events) | ||
|---|---|---|
| SPN/FMI Code | CID-FMI or EID | Description of Code |
| 29-08 | 1249-08 | Secondary Throttle Position signal abnormal |
| 29-13 | 1249-13 | Secondary Throttle Position calibration required |
| 91-08 | 91-08 | Throttle Position signal abnormal |
| 91-13 | 91-13 | Throttle Position calibration required |
| 94-03 | 94-03 | Fuel Pressure open/short to +batt |
| 94-04 | 94-04 | Fuel Pressure short to ground |
| 94-17 | E053 | Low Fuel Pressure Warning |
| 96-03 | 96-03 | Fuel Level Sensor open/short to +batt |
| 96-04 | 96-04 | Fuel Level Sensor short to ground |
| 96-17 | E119 | Low Fuel Level |
| 100-03 | 100-03 | Engine Oil Pressure open/short to +batt |
| 100-04 | 100-04 | Engine Oil Pressure short to ground |
| 100-17 | E100 | Low Engine Oil Pressure Warning |
| 100-18 | E039 | Low Engine Oil Pressure Derate |
| 102-03 | 102-03 | Boost Pressure Sensor open/short to +batt |
| 102-04 | 102-04 | Boost Pressure Sensor short to ground |
| 110-03 | 110-03 | Engine Coolant Temperature open/short to +batt |
| 110-04 | 110-04 | Engine Coolant Temperature short to ground |
| 110-15 | E017 | High Engine Coolant Temperature Warning |
| 110-16 | E015 | High Engine Coolant Temperature Derate |
| 111-17 | E059 | Low Engine Coolant Level Warning |
| 111-18 | E057 | Low Engine Coolant Level Derate |
| 127-03 | 127-03 | Transmission Oil Pressure open/short to +batt |
| 127-04 | 127-04 | Transmission Oil Pressure short to ground |
| 127-15 | E113 | High Transmission Oil Pressure |
| 127-17 | E046 | Low Transmission Oil Pressure Warning |
| 168-02 | 168-02 | System Voltage intermittent/erratic |
| 172-03 | 172-03 | Intake Manifold Air Temp open/short to +batt |
| 172-04 | 172-04 | Intake Manifold Air Temp short to ground |
| 172-15 | E027 | High Inlet Air Temperature Warning |
| 172-16 | E025 | High Inlet Air Temperature Derate |
| 174-03 | 174-03 | Fuel Temperature open/short to +batt |
| 174-04 | 174-04 | Fuel Temperature short to ground |
| 174-15 | E056 | High Fuel Temperature Warning |
| 177-03 | 177-03 | Transmission Oil Temperature open/short to +batt |
| 177-04 | 177-04 | Transmission Oil Temperature short to ground |
| 177-15 | E030 | High Transmission Oil Temperature Warning |
| 190-00 | E004 | Engine Overspeed Shutdown |
| 190-02 | 320-02 | Speed Timing/Sensor Loss of Signal |
| 190-08 | 190-08 | Engine Speed abnormal |
| 190-11 | 320-11 | Speed/Timing Sensor mechanical failure |
| 228-13 | 261-13 | Engine Timing Calibration required |
| 253-02 | 253-02 | Personality Module mismatch |
| 620-03 | 262-03 | 5 Volt Sensor DC Power Supply short to +batt |
| 620-04 | 262-04 | 5 Volt Sensor DC Power Supply short to ground |
| 651-05 | 1-05 | Injector Cylinder 1 open circuit |
| 651-06 | 1-06 | Injector Cylinder 1 short |
| 652-05 | 2-05 | Injector Cylinder 2 open circuit |
| 652-06 | 2-06 | Injector Cylinder 2 short |
| 653-05 | 3-05 | Injector Cylinder 3 open circuit |
| 653-06 | 3-06 | Injector Cylinder 3 short |
| 654-05 | 4-05 | Injector Cylinder 4 open circuit |
| 654-06 | 4-06 | Injector Cylinder 4 short |
| 655-05 | 5-05 | Injector Cylinder 5 open circuit |
| 655-06 | 5-06 | Injector Cylinder 5 short |
| 656-05 | 6-05 | Injector Cylinder 6 open circuit |
| 656-06 | 6-06 | Injector Cylinder 6 short |
| 657-05 | 7-05 | Injector Cylinder 7 open circuit |
| 657-06 | 7-06 | Injector Cylinder 7 short |
| 658-05 | 8-05 | Injector Cylinder 8 open circuit |
| 658-06 | 8-06 | Injector Cylinder 8 short |
| 659-05 | 9-05 | Injector Cylinder 9 open circuit |
| 659-06 | 9-06 | Injector Cylinder 9 short |
| 660-05 | 10-05 | Injector Cylinder 10 open circuit |
| 660-06 | 10-06 | Injector Cylinder 10 short |
| 661-05 | 11-05 | Injector Cylinder 11 open circuit |
| 661-06 | 11-06 | Injector Cylinder 11 short |
| 662-05 | 12-05 | Injector Cylinder 12 open circuit |
| 662-06 | 12-06 | Injector Cylinder 12 short |
| 678-03 | 041-03 | 8 Volt DC Supply short to +batt |
| 678-04 | 041-04 | 8 Volt DC Supply short to ground |
| 723-08 | 342-08 | Secondary Engine Speed signal abnormal |
| 1383-11 | E268 | Unidentified Shutdown |
Show/hide table
| (1) | Suspect Parameter Number |
Caterpillar Information System:
2004/12/01 The Engine Oil Recommendation for 3500 Series Diesel Engines has Changed {1300}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Lifter Group
3408C and 3412C Marine Auxiliary and Marine Generator Set Engines Refill Capacities and Recommendations
345C Excavator Machine System Specifications Stick - 3.4 m (11.16 ft)
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3508C, 3512C and 3516C Marine Engines Piston Cooling Jets - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
390F MHPU Mobile Hydraulic Power Unit Engine Crankcase Breather - Clean
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove