Engine Oil Filter Base - Install
Installation Procedure
All Engines
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install a new O-ring seal and put engine oil manifold (7) in position on the engine.
Show/hide table
Illustration 1 | g00584907 |
- Install nut (6) and tighten the nut to a torque of 80 N·m (59 lb ft).
- Remove the caps or the plugs from the openings and connect hose (3) and hose (4) to the original location on engine oil manifold (7) .
- Put engine oil filter base (2) in position on the engine and install bolts (1) .
Show/hide table
Illustration 2 | g00584891 |
Remote mounted engine oil filter base |
- Remove the caps or the plugs from the openings and connect hose (3) and hose (4) to the original location on engine oil filter base (2) .
- Install engine oil filter (5) onto engine oil filter base (2) .
For engines that are equipped with a turbocharger, refer to "Turbocharged Engines" for more information.
Turbocharged Engines
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Put the gasket and engine oil filter base in position on the engine and install bolt (1) .
Show/hide table
Illustration 3 | g00611406 |
Show/hide table
Illustration 4 | g00611233 |
- Put engine oil cooler (2) in position on the engine oil filter base. Install stud (5) that fastens engine oil cooler (2) to the engine oil filter base.
- Remove the caps or the plugs from the openings and install the hoses and two hose clamps (4). Fill the cooling system to the correct level with coolant.
- Install engine oil filter (3) onto engine oil cooler (2) .
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
D8R Series II Track-Type Tractor General Torque Information
994D Wheel Loader Machine System Piston Pump (Brake) - Disassemble
994D Wheel Loader Machine System Lift Cylinder - Assemble
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Onboard Menu Operation
994D Wheel Loader Machine System Tilt Cylinder - Assemble
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Engine - Clean
3500B Engines Accessory Drive (Upper Right Hand)
D7R Series II Track-Type Tractor Hydraulic System Bulldozer Lift Control Valve
RA1.2, R1.4, R2.0, R2.2, R2.5, R2.7, R3.0, R4.5 and R5.5 Series Reduction Starting Motors Component - Test
3408E and 3412E Engines for Caterpillar Built Machines Crankshaft - Remove
545 Wheel Skidder Power Train Electronic Control Module (Power Train) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Crankshaft - Install
613C Series II Wheel Tractor-Scraper Steering System Piston Pump Oil Leakage (Secondary Steering) - Test
3056 Engines Engine Oil Cooler Bypass Valve
994D Wheel Loader Power Train Pump Drive (Front) - Remove
D8R Track-Type Tractor Cooling System (DEAC) Additive - Add
3054 and 3056 Industrial and Generator Set Engines Water Temperature Regulator Housing
613C Series II Wheel Tractor-Scraper Ejector Carrier Rollers - Check/Adjust
3408E and 3412E Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
545 Wheel Skidder Fuel Tank Water and Sediment - Drain
611 and 615C Series II Wheel Tractor-Scrapers Steering System Steering Time - Check
545 Wheel Skidder Engine Supplement Refrigerant Condenser - Remove and Install