Electronic Unit Injector - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 8T-2998 | 润滑剂 | 1 |
C | 1U-5718 | 真空泵 | 1 |
169-7372 | 油液取样瓶 | 1 | |
4C-4057 | 管
|
1 | |
D | 4C-5552 | 大号孔刷 | 1 |
E | 4C-6774 | 真空枪套件 | 1 |
F | 8T-7765 | 表面调节垫 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (C) 清除缸体上的燃油和机油。 安装电子单体喷油泵之前,尽可能完全排出缸体中的燃油和机油。 可能需要多排几次。
- 使用工具 (D) 清除电子单体喷油泵套筒内的积碳。 可以用工具 (E) 清除电子控制喷油泵套筒和气缸中的松散材料。
- 使用工具 (F) 清除电子单体喷油泵套筒内底座区域的积碳。
- 将 O 形密封圈安装在电子单体喷油器上。 使用按 50/50 比例混合的清洁发动机机油和工具 (B) 润滑一下顶部两个 O 形密封圈。
Show/hide table
图 1 g01114892 Show/hide table注意 当换掉电子控制单体喷油器的时候,新喷油器的代码必须得通过电气伺服工具上的校准菜单编入发动机个人模块软件中。 如果没有输入新喷油器的代码,将会默认应用原来喷油器的特性设置。
如果不可能立刻将喷油器代码编入个人模块软件,对发动机也不会产生很大的伤害。 不过应该尽快编入电子控制单体喷油器的代码,以便能发挥发动机的最大性能。
- 将电子单体喷油器 (2) 安装到缸盖中的原有位置。
- 安装隔套 (5)、卡箍 (6) 和螺栓 (4)。 拧紧螺栓至扭矩为
55 ± 10 N·m (41 ± 7 lb ft) 。 - 将桥接组件 (3) 安装到各自位置。
注: 确保桥接组件上的大孔安装时朝向摇臂。
- 将线束组件 (1) 连接在电子单体喷油器 (2) 上。 拧紧螺母至扭矩为
2.5 ± 0.25 N·m (22 ± 2 lb in) 。
结束:
- 安装摇臂和摇臂轴。 请参阅拆解和组装, "摇臂和摇臂轴 - 安装"。
Caterpillar Information System:
C27 and C32 Generator Set Engines Electronic Unit Injector - Remove
3508C, 3512C and 3516C Marine Engines Water Pump - Assemble
3508C, 3512C and 3516C Marine Engines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C32 Marine and Auxiliary Marine Engines Heat Exchanger
C15 and C18 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
3412E Petroleum Engine Air Inlet and Exhaust Lines
C27 and C32 Industrial and Petroleum Engines Flywheel Housing
390F MHPU Mobile Hydraulic Power Unit Engine Oil Level - Check
390F MHPU Mobile Hydraulic Power Unit Cooling System Coolant Sample (Level 1) - Obtain
C15 and C18 Engines for Caterpillar Built Machines Fuel System
3412E Petroleum Engine Turbocharger
C13, C15, and C18 Tier 4 Final Engines Fuel Filter Base
C27 and C32 Generator Set Engines Electronic Unit Injector Sleeve - Remove
3412E Petroleum Engine Aftercooler
C32 Marine and Auxiliary Marine Engines Aftercooler
C9.3 Engine for Caterpillar Built Machines Valve Mechanism
3126B Engine for Caterpillar Built Machines Flywheel Housing
390D Excavator Access Door and Cover Locations
G3406 and G3412 Generator Sets Voltage Regulators
C27 and C32 Industrial and Petroleum Engines Air Lines
C32 Marine and Auxiliary Marine Engines Alternator Mounting
2005/11/14 Improvements to Turbocharger and Exhaust Manifold Groups {1052, 1059, 1061}
3508B, 3512B and 3516B Generator Set Engines Aftercooler - Remove and Install