Vane Motor (Elevator) - Assemble
Assembly Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Group | 1 |
| B | 1P-1859 | Retaining Ring Pliers | 1 |
| C | 1U-6684 | Compressor | 1 |
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
- Install seal (27) , O-ring seal (26) and O-ring seal (25) to body (4) .
Show/hide table
 | |
| Illustration 1 | g00449160 |
- Lubricate lip seal (24) lightly with the lubricant that is being sealed. Use Tool (A) to install lip seal (24) to body (4) .
Show/hide table
 | |
| Illustration 2 | g00449159 |
- Install washer (23) to body (4) .
Show/hide table
 | |
| Illustration 3 | g00449158 |
- Use a hydraulic press to install roller bearing (22) to shaft assembly (21) . Install the roller bearing until the roller bearing contacts the lip of the shaft.
Show/hide table
 | |
| Illustration 4 | g00449723 |
- Use a hydraulic press to install shaft assembly (21) to body (4) . Install the shaft assembly until the shaft assembly is seated in the body.
Show/hide table
 | |
| Illustration 5 | g00449724 |
- Use Tool (B) to install retaining ring (20) to shaft assembly (21) .
Show/hide table
 | |
| Illustration 6 | g00449155 |
- Install O-ring seal (19) and seal (18) to ring (17) .
Show/hide table
 | |
| Illustration 7 | g00449154 |
- Install ring (17) to body (4) .
Show/hide table
 | |
| Illustration 8 | g00449153 |
- Install O-ring seal (16) to plate assembly (14) .
Show/hide table
 | |
| Illustration 9 | g00449152 |
- Use Tool (C) to install rotor assembly (15) to ring (12) .
Show/hide table
 | |
| Illustration 10 | g00449730 |
- Install dowel pins (13) , ring (12) , plate assembly (11) and two bolts (10) to plate assembly (14) .
Show/hide table
 | |
| Illustration 11 | g00449150 |
- Install cartridge (9) and seal (8) to body (4) .
Show/hide table
 | |
| Illustration 12 | g00449149 |
- Install O-ring seal (7) to cover (2) . Install swivel adapter (6) to cover (2) and tighten retaining nut (5) .
Show/hide table
 | |
| Illustration 13 | g00449148 |
- Install cover (2) and four bolts (3) to body (4) . Install plug (1) to cover (2) .
Show/hide table
 | |
| Illustration 14 | g00449147 |
End By: Install the elevator motor. Refer to Disassembly and Assembly, "Vane Motor (Elevator) - Install". The information is in this manual.
Caterpillar Information System:
631E Series II Wheel Tractor-Scrapers Hydraulic Oil Cooler - Clean - Auger
Installation Procedure Of The HEUI Pump Compensator Standby Plug For 3408E And 3412E Engines{1714} Installation Procedure Of The HEUI Pump Compensator Standby Plug For 3408E And 3412E Engines{1714}
D9R Track-Type Tractor Starting with Auxiliary Start Receptacle
623F Wheel Tractor-Scraper Hydraulic Oil Cooler - Clean
994D Wheel Loader Power Train Transmission Pressures - Test and Adjust
994D Wheel Loader Link Pin Oil Level - Check
994D Wheel Loader Power Train Bearing End Play (Rear Pump Drive) - Adjust
IT14G Integrated Toolcarrier Creeper Speed Control - If Equipped
615C Series II Wheel Tractor-Scraper Machine Systems Vane Motor (Elevator) - Disassemble
994D Wheel Loader Power Train Bearing End Play (Drive Shaft Support) - Adjust
Payload Control System Owner Setup Functions
D8R Track-Type Tractor Prestart Checks
Payload Control System System Calibration
615C Series II Wheel Tractor-Scraper Machine Systems Vane Motor (Elevator) - Remove
627F Wheel Tractor-Scraper Windows - Clean
615C Series II Wheel Tractor-Scraper Machine Systems Vane Motor (Elevator) - Install
Payload Control System Normal Weighing Mode
994D Wheel Loader Cab Air Filter - Clean/Replace
Payload Control System Keypad Modes and Functions
D8R Track-Type Tractor Ether Starting Aid
994D Wheel Loader Power Train General Information
615C Series II Wheel Tractor-Scraper Machine Systems Tire and Rim - Remove
D8R Track-Type Tractor Engine Start Switch
966G and 972G Wheel Loaders Power Train Axle Housing - Disassemble