Electric Starting Motor
Show/hide table
Illustration 1 | g01093287 |
Show/hide table
Illustration 2 | g01093288 |
When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... Clockwise
No load conditions at 25 °C (77 °F)
- Speed ... 7643 ± 1683 rpm
- Current draw ... 76.5 ± 14.5 amp
- Voltage ... 23 V
- Current draw ... 76.5 ± 14.5 amp
(1) Battery terminal
-
A maximum of three cable or wire terminals should be between the nuts.
- Tighten the nut on the battery terminal to the following torque. ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(2) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(3) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
(4) Switch terminal
-
The wire terminal that is on the switch terminal must be insulated with heat shrink tubing. Do not use molded terminals.
- Tighten the nut on the switch terminal to the following torque. ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
(5) Motor terminal
- Tighten the nut on the motor terminal to the following torque. ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(6) Motor frame terminal
- Tighten the nut on the motor frame terminal to the following torque. ... 8 ± 3 N·m (70 ± 24 lb in)
Clearance between the pinion and the housing ... 9.1 mm (0.36 inch)
Solenoid
Current draw at 20 V and 25 °C (77 °F)
- Pull-in windings ... 57 Amp
- Hold-in windings ... 16 Amp maximum
Caterpillar Information System:
C15 and C18 Industrial Engines Water Temperature Regulator Housing - Remove and Install
C9 Marine Engines and C9 Marine Generator Sets Electric Starting Motor
Installation of the Uninterruptible Power Supply (Single-Module System){4480} Installation of the Uninterruptible Power Supply (Single-Module System){4480}
C9 Marine Engines and C9 Marine Generator Sets Alternator and Regulator
C9 Marine Engines and C9 Marine Generator Sets Alternator and Regulator
2004/08/01 An Improved Injection Actuation Pressure Sensor Is Now Used {1925}
EMCP3 Spare Analog Input Programming
EMCP3 Digital Input Programming
EMCP3 Component Location
3500 Engines for Caterpillar Built Generator Sets Prelube Pressure Switch
2004/08/01 An Improved Injection Actuation Pressure Sensor Is Now Used {1925}
3412E, C30 and C32 Marine Engines Engine Oil Pump - Install
C9 Marine Engines and C9 Marine Generator Sets Electric Starting Motor
2004/08/01 Maintenance Considerations for Engines in Landfill Applications {1000}
G3612 and G3616 Engines Product Description
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Bypass Valve (Transmission Oil Filter)
C18 Marine Generator Set Battery - Replace
3516C Locomotive Engine Safety Messages
C9 Marine Generator Set Engines Charging System - Test
Some Original Part Numbers Have Been Discontinued{1000, 7000, 7567} Some Original Part Numbers Have Been Discontinued{1000, 7000, 7567}
C9 Marine Engines CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C9 Marine Engines CID 0175 FMI 04 Engine Oil Temperature short to ground
C3.3 Industrial Engine Before Starting Engine
XQ60 Rental Generator Set Engine Stopping